Installation Guide

OUTLET BOX
HOUSE SUPPLY and
GROUND WIRES
OUTLET BOX SCREWS
not supplied()
GREEN GROUND SCREW
CROSSBAR
SHAKE PROOF
WASHER A
LOCK NUT A
NIPPLE
LOCK NUT B
SHAKE PROOF
WASHER B
CANOPY CHAIN LOOP
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE CHAIN
CEILING CANOPY
CANOPY LOCK RING
FIXTURE SUPPLY
and GROUND WIRE
FIXTURE LOOP
FIXTURE
COVER
LOCK SCREW
SOCKET
TAB
GLASS PANEL
LOCK
SCREW
CAGE
1 Before beginning the installation carefully unpack and
identify all parts referring to the illustration
2 Turn power to the installation point OFF at circuit breaker
3 Slip down the GLASS PANELinsideof CAGE. Locate TAB
onto the top edge of GLASS PANELandmatch the hole on
it with mounting hole on the top edge of CAGE. Thread LOCK
SCREW into the mounting hole and hand tighten until snug
to secure it. Repeat this progress to complete the rest
GLASS PANELS.
4. Position FIXTURE COVER onto the top edge of CAGE and
match the mounting hole inside of it with holes on the top
corners of CAGE. Secure them together by threading LOCK
SCREWS into the mounting holes. Hand tighten until snug.
Proceed to thread FIXTURE LOOP onto the nipple on the
top center of FIXTURE COVER. Hand tighten until snug.
5 Fasten the CROSSBAR to the OUTLET BOX with (2)OUTLET
BOX SCREWS(not supplied). Proceed to thread LOCK
NUT A and SHAKE PROOF WASHER A onto the top end of
NIPPLE. Thread NIPPLE into the center of CROSSBAR.
Locate the LOCK NUT B onto the bottom end of the NIPPLE.
Tighten LOCK NUT A against CROSSBAR with plier until snug.
6. Locate the FIXTURE CHAIN and determine desired hanging
height of fixture.Adjust chain by removing links if needed.
Please note that depending on chain material thickness, you
might be required to use chain pliers to spread links open.
Proceed to attach one end of chain to FIXTURE LOOP,
attached to top of fixture. Pass the fixture wires through
FIXTURE CHAIN alternating links. Proceed to pass the fixture
wires through the following mounting components in this order:
1)CANOPY LOCK RING; 2)CEILING CANOPY 3 CANOPY
CHAIN LOOP 4 SHAKE PROOF WASHER B and LOCK
NUT B 5 NIPPLE 6 LOCK NUT A and SHAKE PROOF
WASHER A
7.
(2 people recommended for the remaining steps) Position the
fixture under the ceiling mounted outlet box. Pass SHAKE
PROOF WASHER B over the NIPPLE. Thread CANOPY
CHAIN LOOP onto NIPPLE. Thread LOCK NUT B down the
NIPPLE, against the CANOPY CHAIN LOOP and snug with
pliers. Pass the wires through the NIPPLE. Take up wire slack
and trim wires so that approx. 6” will remain inside outlet box.
Proceed to attach the top of the FIXTURE CHAIN to the bottom
of the CANOPY CHAIN LOOP. Using wire connectors (not
supplied) connect the HOUSE GROUND WIRE to the
FIXTURE GROUND WIRE connect the HOUSE WHITE
WIRE to the FIXTURE SUPPLYWIRE (WHITE or RIBBED
SIDE); connect the HOUSE BLACK (or RED) WIRE to the
FIXTURE SUPPLYWIRE(BLACK or SMOOTH SIDE). Wrap
each connection with approved electrical tape.
8. With the proper connections made, proceed to push the
CEILING CANOPY upward over the OUTLET BOX. Be sure
that all wires are carefully tucked into the OUTLET BOX cavity.
Secure canopy against ceiling by threading CANOPY LOCK
RING onto the CANOPY LOOP. Tighten until snug.
9.Install bulb referring to fixture markings and/or labels for
maximum wattage.
10 Restore power to the installation point ON. Retain this sheet
for future reference.
.
..
.
,
,.
.
;)
;)
;) ; )
.
;
.
Making the connections:
ASSEMBLY / INSTALLATION INSTRUCTIONS
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION,
CONSULT A LICENSED ELECTRICIAN!
IS-HC1913
2007-01-03
FIRST DRAFT