Installation Guide

1of2
Assembly Instruction Sheet #IS-HTR9008IB
For Style HTR9008IB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
November2014
Package Contents
E
C
Shade
x1
A
Mounting
Screw
x3
D
Fixture Body
x1
Lock
Screw
x2
STEP 2 Install Shade-
A. Place Shade (D) into the Shade
Holder.
B. Place Fixture Hood (B) over the
Fixture Body (D),secure by threading
the Lock Screw (E) into the Fixture
Hood (B), tighten until sung.
Figure 2
B
C
D
E
B
Fixture
Hood
x1
STEP 1 Install Bulb-
A. This fixture uses standard bulb with
medium screw base. Maximum 150
watts.
B. Insert bulb and screw snugly into
place.
Figure 1
Bulb
Socket
STEP 3 Drill Pilot Holes on
Post
-
A. Carefully fit the Post Fitter over
the end of the Post (not
supplied), making sure the
Post Fitter is fully seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference.
After marking hole locations,
remove fixture from post and
drill 1/16” pilot holes for
screws.
Post
Post Fitter
Figure 3
Shade
Holder
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters,wire strippers,electrical tape,safety glasses.
BulbRecommended: (1) MediumBase 150WMaximum,Alternatebulb (1)42W CFL
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperatethefixture.Contact customerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering November result.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Attach Fixture Body to
Post
-
A. Coat the top 1” of the Post with
Clear Silicone Caulk (not
supplied) and position the Post
FitterontothePost.Besureto
seat it completely, aligning the
holes in the Fitter with the 1/16”
Pilot Holes drilled into the Post.
B. Secure the Fixture to Post with
(3) Mounting Screws.
Your fixture is now assembled
and ready to use. Enjoy!
Mounting
Hole
Post
Fitter
Mounting
Screw
Post
Figure 5