Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)MediumBase75WbulbMaximum,Alternatebulb(2)19WCFLMaximum.
15-20minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
Estimated Assembly Time:
Preparation:
ToolsRequired:None.
1of1
Assembly Instruction Sheet #IS-JD2077TVB
For Style JD2077TVB
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
July2015
JD2077TVB
FINISH: VINTAGE BRONZE
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
A. Thread the Hex Nut end of
the Nipple with Hex Nut into
the Hex Coupling on the top
center of the Base. By using
pliers, thread the Hex Nut
against the Hex Coupling
and hand tighten until snug.
B. Place the Spacer Tube and
the Check Ring over the top
end of the Nipple and
secure with the Small
Knurled Nut. Hand tighten
until snug. Thread the Big
Knurled Nut onto the Nipple
and adjust it to proper
location for rest
components.
C. Place the Shade over the
Nipple. Secure by threading
the Finial onto the Nipple.
Hand tighten until snug.
D. This fixture uses standard
bulb with medium base .
Maximum 75 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
use. Enjoy!
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
(2) 75W
Bulbs
(Not Supplied)
Medium
Base
1
2
Base
x1
Big Knurled
Nut x 1
Small Knurled
Nut x 1
Check Ring
x1
Spacer Tube
x1
Nipple with
Hex Nut
x1
Hex Coupling
PART NUMBER REPLACEMENT PART
NO.
1
12077TVBJD
BASE
REQ.
1
2
G12081SH SHADE
1
15.75”Dia.
7.5”
23.5”
6.75”Dia.
Bulb
Shade
x1
Finial
x1