Installation Sheet
1of2
For Styles LRY5022Y and LRY1722Y
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(4)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
MinimumHangingHeightis26”,MaximumHangingHeightis74”.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
FixtureHangingHeight:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Note:This CONVERTIBLEfixturecanbemountedaschandelierlightorsemi-flushlight.Refertorespective
installationsteps forinstallations.
Installation Guide
2019 QuoizelInc.
visit us on-line at www.quoizel.com
ReleasedDate:2019-04-04
Package Contents
Ceiling Canopy
x1
Fixture Chain
x1
Quick Link
x2
B
C
D
Canopy
x1
Loop
E
Fixture Body
x1
I
H
Glass
x4
A
Crossbar Assembly
x1
Fixture Loop
x1
F
Center Column
x1
G
Assembly Instructions for Chandelier Light: LRY5022Y
(Step 1A - Step 8A)
G
F
STEP 1A - Install the Fixture Loop and the Center Column
A. Thread the Fixture Loop , the Center Column and the
(I) together as shown. Hand tighten until snug.
(F) (G) Fixture
Body
I
Figure 1A
STEP 2A - Install the Canopy Loop
A. Thread the Canopy Loop
and tighten
until snug.
(E) to the
Ceiling Canopy (D) and h
D
E
Figure 2A
STEP 3A - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 3A
STEP 4A Test Fitting Ceiling Canopy to Crossbar Assembly-
A.
to the
ceiling
Remove mounting balls from the Crossbar Assembly (A). Fit the
Crossbar Assembly (A) and secure with
mounting balls. Note: The should be snug against
the and the mounting balls. If
Ceiling Canopy (D)
Fixture Canopy
not, adjust the length of the
mounting screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy (D) is secure, remove the
mounting ball and .Ceiling Canopy (D)
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
D
Figure 4A