Installation Sheet

ManualsBrandsQuoizel ManualsLighting & Ceiling FansMarblehead 17.75-in H Fresco Candelabra Base (E-12) Outdoor Wall Light

1of2

Figure 3

STEP 2 Install Crossbar Assembly-

A. Pass the supply wires through the Crossbar Assembly (AA). Attach

the Crossbar Assembly (AA) to the Outlet Box with the head of the

Green Ground Screw facing you. Secure it with Outlet Box Screws

(not included). Tighten until snug

Note: Use the Alternate Shorter Mounting Screw (BB) if your

installation requires a shorter mounting screw.

STEP 3 Test Fit the Backplate to the Crossbar Assembly-

A. Remove the mounting balls from the Crossbar Assembly (AA).

Place the backplate and Fixture Body (A) onto the Crossbar

Assembly (AA) and secure with mounting balls. Note: The

backplate and Fixture Body (A) should be snug against the wall and

held tight with the mounting balls. If it is not, adjust the length of the

mounting screws or alternate short mounting screws on the

Crossbar Assembly (AA) by unscrewing the preassembled hex nut

and lock washer and then screwing the mounting screws or

alternate short mounting screws in or out of the crossbar until the

correct length is achieved. Once the backplate and Fixture Body (A)

Pleasegoto forproductcleaningtips.Gotothe selection.

Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

(3)B10CandelabraBaseBulbs60WMaximum

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

www.quoizel.com Care+Maintenance

ToolsRequired:

LightSource:

EstimatedAssemblyTime:

Preparation:

Fixturecanonlybemountedinthedirectionindicatedonpage2.

Warnings and Cautions

Assembly Instruction Sheet #IS-MBH8411W

For Style MBH8411W

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Mounting Screw

or Alternate Short

Mounting Screw

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

Hex Nut and

Lock Washer

Mounting Ball

Mounting Screw

or Alternate Short

Mounting Screw

Backplate

2017 QuoizelInc.

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184

or visit us on-line at www.quoizel.com

is secure, remove the

mounting ball and

Fixture Body (A) and

proceed to Step 4.

Hardware Contents

Package Contents

Cage

Tab

Crossbar

Assembly

STEP 1 Install Shade-

A. Place the Glass Shade (C) into the

Cage (D). Secure by pressing Tabs

(B) onto the Cage (D) and top edge

of the Glass Shade (C).

B. Place the sockets of the Fixture

Body (A) inside of the Glass Shade

(C). Align the label “A” on the bottom

edge of the fixture hood to the label

“A” on the top edge of the Cage (D).

Attach the fixture hood of the Fixture

Body (A) to the top edge of the Cage

(D). Secure them together with Lock

Screws (E). Hand tighten until snug

with screwdrivers.

Fixture

Body

Glass Shade

Figure 1

Lock Screw

Alternate

Mounting

screw

Label “A”

ReleasedDate:2017-08-02

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-MBH8411W For Style MBH8411W 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
PAGE 2
STEP 4 - Wire Connections MBH8411W A. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. White wire from outlet box White wire from fixture Black wire from outlet box (or Red) Black wire from fixture Bare, or Green Ground wire from outlet box FINISH: FRESCO 12” 11” Dia.