Installation Guide

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
Package Contents
Pleasegoto forproduct cleaningtips. Goto the selection.
(1)A21MediumBase bulb150W Maximum,Alternatebulb(1) 42WCFL.
www.quoizel.com Care+ Maintenance
LightSource:
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.
EstimatedAssemblyTime:
Preparation:
20-30minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
STEP 4 Attach Fixture Body to
Post
-
A. Coat the top 1” of the Post with
Clear Silicone Caulk (not supplied)
and position the Post Fitter onto
the Post. Be sure to seat it
completely, aligning the holes in
the Fitter with the 1/16” Pilot Holes
drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws (A).
Your fixture is now assembled and
ready to use. Enjoy!
A
Mounting Screw
x3
F
Cage
x1
STEP 1 Install Bulb and
Fixture Hood
-
A. Insert Glass Panel (G) into
the Slot in the Cage (F). Line
up the hole on the Glass
Holder (E) and the mounting
hole on the Cage (E), secure
by threading Short Lock
Screw (B) into the Mounting
Hole, hand tighten until
sung.
B. This fixture uses standard
bulb with standard screw
base. Maximum 150 watts.
Insert bulb and screw snugly
into place.
C. Line up the hole on the
Fixture Body (D) and the
mounting hole on the Cage
(F), secure by threading
Long Lock Screw (C) into
the mounting hole, tighten
until sung.
Bulb
Socket
Figure 1
Assembly Instruction Sheet #IS-MLS9007IB
For Style MLS9007IB
Post
Post Fitter
Figure 4
Mounting Hole
A
B
Short Lock Screw
x8
D
Fixture
Body
x1
September2015
G
Glass
Panel
x4
E
Glass
Holder
x4
G
F
E
B
Slot
C
D
STEP 2 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied),
making sure the Post Fitter is fully
seated.
B. Mark the drill point for the (3)
Mounting Screws, using (3)
Mounting Holes as reference. After
marking hole locations, remove
fixture from post and drill 1/16” pilot
holes for screws.
Figure 2
Post
Post Fitter
Mounting Hole
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
C
Long Lock Screw
x4