Installation Sheet

Package Contents
1of2
For Style NL8601EK
A
Crossbar
Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBaseBulb100WMaximum,bulbnotincluded.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactyouroriginalplaceofpurchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
STEP 1 - Install the Crossbar
Assembly to the junction box
A. Attach the Crossbar Assembly (A)
to the outlet box with the head of
green ground screw facing you.
Secure it with Outlet Box Screws
(not included), tighten until snug.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Installation Guide #IS-NL8601EK
2019 QuoizelInc.
ReleasedDate:2019-01-16
visit us on-line at www.quoizel.com
Fixture Body
x1
B
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Glass Shade
x1
C
Socket Collar
x1
D
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
Green
Ground
Screw
STEP 2 Test fitting the backplate to the Crossbar Assembly-
A. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
B. Remove the mounting ball from the nipple. Place the backplate and
Fixture Body (B) over the nipple against the wall to determine the
correct position of the nipple. Thread the mounting ball onto the
Hex Nut and
Lock Washer
Nipple
Mounting Ball
B
Backplate
Figure 2
nipple. Adjust the nipple to
allow the backplate to rest
against the wall when held in
place by the mounting ball.
C. Remove the mounting ball
and the Fixture Body (B).
Tighten the lock washer and
the hex nut against the
crossbar to secure in place.
STEP 4 - Install the Fixture
Body
A. Place the backplate of the
Fixture Body (B) onto the
nipple and secure with
previously removed mounting
ball. Hand tighten until snug.
Nipple
Mounting Ball
B
Backplate
Figure 4
STEP 5 - Install Glass Shade and Bulb
A. Place the Glass Shade (C) over the
socket and secure with the Socket
Collar (D). Hand tighten until snug.
B. Insert the bulb onto the socket and
screw snugly into properly.
Your fixture is now assembled and
ready to use. Enjoy!
B
Bulb (not
included)
Socket
C
D
Figure 5