Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.www.quoizel.com Care+Maintenance
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
LightSource:
EstimatedAssemblyTime:
Preparation:
(2)MediumBase60WMaximum,Alternatebulb (2) 13W CFLand (1) 7W C7 Candelabra Base Bulb (supplied).
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-NX615
For Style NX615TVA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 QuoizelInc.
April2015
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
A. Thread the Hex Nut onto the
Nipple and then thread the
Nipple into the Hex Coupling on
the top center of the Base. By
using pliers, thread the Hex Nut
against the Hex Coupling and
hand tighten until snug.
B. Place the Spacer Tube and the
Check Ring over the Nipple.
Secure by threading the Small
Knurled Nut onto the Nipple.
Hand tighten until snug.
C. Thread the Big Knurled Nut onto
the Nipple and adjust it to proper
location for the Shade and the
Finial.
D. Place the Shade over the Nipple
and secure with the Finial. Hand
tighten until snug.
E. This fixture uses standard bulb
with medium base . Maximum 60
watts. Insert bulb and screw
snugly into place.
Your fixture is now assembled
and ready to use. Enjoy!
Finial
x1
Shade
x1
Bulb (not
included)
Big Knurled
Nut x 1
Check Ring
x1
Spacer Tube
x1
Small
Knurled
Nut
x1
Base
x1
Hex Coupling
Nipple
x1
Hex Nut
x1
How To Replace C7 Bulb
A. Remove Shade, Spacer Tube and
Nipple from fixture.
B. Unlock Lock Screws from the Base
and remove Socket Assembly from the
Base.
C. Replace the C7 7W Bulb. Screw
snugly into place.
D. Reinstall the Socket Assembly onto
the Base and assemble Nipple,
Spacer Tube and Shade.
Base
Base
Socket
C7 Bulb
Lock
Screw
Socket
Assembly