User Manual

Quoizel, Inc.
6 Corporate Parkway
Goose Creek, SC 29445
Customer Service
Phone [phone]
Fax [phone]
www.quoizel.com
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape,
safetyglasses.
EstimatedAssemblyTime:20-30minutes
Preparation:Identify andinspect allparts beforebeginning installation.Check packagecontent listand diagrams
belowto besure allparts arepresent. Ifany partsare missingor damaged,do notattempt toassemble, install,or
operatethe fixture.Contact customerservice forreplacement parts.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-OZ1616
For Style OZ1616PN and OZ1616IN
BulbRecommended: (3) MediumBase 60WMaximum,Alternatebulb(3) 13WCFL
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
March2014
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
A
D
C
Hardware Contents
Ceiling
Canopy
x1
Shade
Holder
x1
Lock Ball
x3
AA
CC
DD
BB
Crossbar
x1
Lock Washer
x1
Hex Nut
x2
Nipple
x1
G
Flat
Washer
x6
STEP 1 Install Crossbar-
A. AA)Attach the Crossbar ( to
the Outlet Box with the head of
the Green Ground Screw
facing you. Secure it with
Outlet Box Screws (not
included) Tighten until snug..
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground Screw
AA
EE
Big Flat Washer
x1
STEP 2 - Attach Nipple to Crossbar
A. Thread one Hex Nut (DD) onto the top end of the Nipple (BB).
B. Place one Lock Washer (CC) over the top end of the Nipple (BB) and
then thread the Nipple (BB) into the center lock hole of the Crossbar
(AA).
C. Using pliers, thread the Hex Nut (DD) against the Crossbar (AA) and
hand tighten until snug.
Figure 2
AA
CC
DD
BB
DD
A
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Strip and
prepare wire ends according to instructions supplied with
connectors.
B. Connect White Supply Wire from the Outlet Box to Ribbed side
Wire from fixture.
C. Connect Black (or Red) Supply Wire from the Outlet Box to Smooth
side Wire from fixture.
D. Connect Ground Wire from the Outlet Box to Ground Wire from
fixture.
E. Twist connectors until wires are tightly joined together.
F. Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
FF
Allen Wrench
x1
E
Allen Bolt
x3
B
Finial
x1
F
Rubber
Washer
x3
H
Shade
x1
White wire
from supply
Ribbed side wire
from fixture
Black wire from
supply (or Red)
Smooth side wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 3
D. Thread the other Hex Nut (DD) onto the other end of the Nipple
(BB). Thread this Hex Nut (DD) on just enough so the inside
surface of the Ceiling Canopy (A) rests against it. * You may have
to trial fit the Ceiling Canopy (A) one more times to insure this
distance also. This Hex Nut (DD) is needed here to prevent you
from crushing down the center of the Ceiling Canopy (A).