Installation Sheet

1of2
Assembly Instruction Sheet #IS-QF3411BN
For Style QF3411BN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
ReleasedDate:2017-11-29
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)A19MediumBaseBulbs60WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired: Flathead screwdriver,Phillips screwdriver,pliers, wire cutters, wire strippers, electrical tape, safety glasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
STEP 3 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
B
C
Glass Holder
x1
D
Lock
x3
Screws
Glass Shade
x1
E
STEP 1 Install Crossbar Assembly-
.
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
Figure 1
STEP 2 - Test Fit the Ceiling Canopy to the Crossbar Assembly
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the Ceiling Canopy and Fixture Body (B) onto the Crossbar
Assembly (A) and secure with mounting balls. Note: The Canopy
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box
A
(Step 2 Continued)
and Fixture Body (B) should be snug against the Ceiling and held
tight with the mounting balls. If it is not, adjust the length of the
mounting screws on the Crossbar Assembly (A) by unscrewing the
preassembled hex nut and lock washer and then screwing the
mounting screws in or out of the crossbar until the correct length is
achieved. Once the Ceiling Canopy and Fixture Body (B) is secure,
remove the mounting ball and Fixture Body (B) and proceed to
Step 3.
Figure 2
Hex Nut and
Lock Washer
B
Mounting Ball
A
Mounting Screw
Ceiling Canopy