Installation Sheet

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)A19MediumBaseBulbs75WMaximum
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-QF3414BN
For Style QF3414BN
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Package Contents
ReleasedDate:2017-08-24
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Shade
x1
Stem
x1
Fixture Body
x1
F
Hex Coupling
x1
G
H
I
J
Cap
x1
A
Crossbar
Assembly
x1
B
Lock Washer
x1
D
Flat Washer
x2
C
E
Rubber Washer
x1
Hex Nut
x1
K
Finial
x1
STEP 1 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
Outlet Box Screw
(not included)
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Figure 1
Nipple
Hex Nut
Ceiling
Canopy
E
D
A
(Step 1 Continued)
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (not included), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Place the ceiling canopy and Fixture Body (E) over the end of the
nipple against the ceiling to determine the correct position of the
nipple. Thread the Hex Coupling (D) onto the nipple. Adjust the
nipple to allow the ceiling canopy and Fixture Body (E) to rest
against the ceiling when held in place by the Hex Coupling (D).
D. Remove the Hex Coupling (D) and the Fixture Body (E). Tighten the
lock washer and the hex nut against the crossbar to secure in place.
E. Adjust another hex nut on the end of nipple just enough so that the
inside surface of ceiling canopy and Fixture Body (E) rests against it.
You may have to trial fit ceiling canopy and Fixture Body (E) one
more times to insure this distance also. This hex nut is needed here
to prevent you from crushing down the center of ceiling canopy.
.
Figure 2
STEP 2 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture