Installation Sheet

ManualsBrandsQuoizel ManualsCeiling FixturesQuoizel Hydra 3 Light 14" Wide Semi-Flush Ceiling Fixture

1of2

For Style QF4062IB

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.

Pleasegoto forproductcleaningtips.Gotothe selection.

(3)A19MediumBase60WMaximum,bulbnotincluded.

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssembly Time:

Preparation:

ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Installation Guide #IS-QF4062IB

2018 QuoizelInc.

visit us on-line at www.quoizel.com

Package Contents

Crossbar Assembly

Ceiling Canopy

STEP 2 - Installing the Crossbar Assembly

A. Pass the supply wires from outlet box through the Crossbar

Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw facing you. Secure the

Crossbar Assembly (A) with Outlet Box Screws (not included).

Tighten until snug.

Supply Wires with

Ground Wire

Outlet Box Screws

(not included)

Outlet Box

Figure 2

STEP 3 Test Fitting Ceiling Canopy to Crossbar Assembly-

eiling Canopy to the

ceiling

Remove mounting balls from the Crossbar Assembly (A). Fit the

C Crossbar Assembly (A) and secure with

mounting balls. Note: The should be snug against

the and the mounting balls. If

Ceiling Canopy

not, adjust the length of the

nipple on the Crossbar Assembly (A) by unscrewing the

preassembled hex nut and lock washer and then screwing the

mounting screws in or out of the crossbar until the correct length is

achieved. Once the Ceiling Canopy (B) is secure, remove the

mounting ball and Ceiling Canopy and proceed to Step 4.

Mounting Screw

Hex Nut and

Lock Washer

Mounting Ball

Figure 3

STEP 4 - Wire Connections

B. Use standard wire connectors (not included) to make all wire

connections. Twist connectors until wires are tightly joined together.

Wrap each connection with approved electrical tape and carefully

stuff all the connected wires into the Outlet Box.

Wrap bare or green ground wire around green ground screw on the

crossbar, no less than 2 inches from the end of the wire. Tighten the

green ground screw.

Figure 4

Green Ground Screw

on the Crossbar

White wire

from outlet box

White wire

from fixture

Black wire from

outlet box (or Red)

Black wire

from fixture

Bare, or Green

Ground wire

from outlet box

Ground wire

from Fixture

ReleasedDate:2018-10-22

Figure 5

STEP 5 Install the Fixture-

A. Carefully tuck all wires into the outlet box and position the Ceiling

Canopy over the outlet box. Align the holes in the ceiling canopy

with the mounting screws, then attach the Ceiling Canopy using the

previously removed mounting balls. Hand tighten until snug.

Fixture Body

Nipple Assembly

STEP 1 - Installing the Ceiling Canopy

b. Pass supply wires and ground wire

through the Ceiling Canopy (B).

Thread Ceiling Canopy ( ) onto the

Fixture Body ( ), hand tighten until

snug.

c. B

a. B rod

Thread Ceiling Canopy ( ) onto the

( ), hand tighten until snug.

Figure 1

Mounting Screw

Mounting Ball

Diffuser

Rod

Summary of content (2 pages)

PAGE 1
Installation Guide #IS-QF4062IB For Style QF4062IB Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (3) A19 Medium Base 60W Maximum, bulb not included. Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
QF4062IB STEP 6 - Remove the finial A. Remove the finial, hex nut, rubber washer and flat washer from the stem assembly. FINISH: IMPERIAL BRONZE Figure 6 Rubber Washer Flat Washer Hex Nut Finial D STEP 7 - Install the Diffuser a. Thread the nipple onto the coupling on fixture. Hand-tighten until snug. b. Place diffuser and the previously removed rubber washer and flat washer over the nipple. Secure with the previously removed hex nut. Hand-tighten until snug. c. Thread the finial onto the nipple.