Installation Sheet

ManualsBrandsQuoizel ManualsShop All QuoizelQuoizel Intensity 32 Inch x 24 Inch Rectangular Flat Iron Wall Mounted Vanity Mirror

1of3

For Style QR3700

Pleasegoto forproductcleaningtips.Gotothe selection.

markingpen,1/ ”

drillbit drill.

IntegratedLED37W

30-45minutes

Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof

purchase.

www.quoizel.com Care+Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses, 8

and

Note:This mirrorcan bemounted overan electricaloutlet boxor onthe walland pluggedinto anoutlet.

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Package Contents

Screw

Mirror

Wall Anchor

Cord Cover

Backplate

Cord Cover

DIRECT MOUNTING MIRROR TO THE WALL

Installation Guide #IS-QR3700

2018 QuoizelInc.

ReleasedDate:2018-04-16

visit us on-line at www.quoizel.com

Step 1A - Identify Locations for Wall Anchors

A. The template is provided to assist you in mounting the mirror. The

template is a full size drawing of your mirror and includes the wall

anchor mounting locations that can easily be transferred to the wall,

or use the mirror.

Mark Wall Anchor

Locations On The Wall

At Arrow Locations

Step 2A - Installing 4 Wall Anchors and Screws

A. Using a 1/8” drill bit, drill holes at each (4) locations marked on the

wall surface.

B. Insert Wall Anchors (B) into drilled holes completely.

C. Attach Mounting Plates (F) to the Wall Anchors (B) and secure by

threading Screws (A) into Wall Anchors (B). Hand tighten until snug

with screwdrivers.

Mark

Mounting

Plate

TEMPLATE

Figure 1A

(Step 1A Continued)

Place the template or the mirror on the wall in the location selected

for the mirror. Make sure the template or mirror is level and in the

correct position. Secure the template to the wall then mark the

locations of the 4 wall anchors as indicated on the template. Remove

the template from the wall.

Figure 2A

STEP 3A Hang Mirror-

A. With the help of another

person place the hanging bar

on the back of the Mirror (E)

onto Mounting Plates (F).

Making sure hanging bar is

securely hung onto Mounting

Plates (A) before letting go of

the Mirror (E).

Figure 3A

Hanging Bar

Summary of content (3 pages)

PAGE 1
Installation Guide #IS-QR3700 For Style QR3700 Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses, marking pen, 1/ 8 ” drill bit and drill. Light Source: Integrated LED 37W Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation.
PAGE 2
STEP 4A - Install Cord Cover Backplate and Cover Covers Step 2B - Insert Cord for Horizontal Mounting and Making the Wire Connections A. Align the Cord Cover Backplate (C) to your desired location on the wall. Mark the mounting locations on the wall from the holes on the Cord Cover Backplate (C). B. Drill a hole for Wall Anchors (B) at each location identified with a 1/8” drill bit. Place the Wall Anchor (B) into each hole. C. Attach the Cord Cover Backplate (C) by using Screws (A).
PAGE 3
STEP 2C - Wire Connections QR3700 A. Wrap bare or green ground wire around green ground screw on the crossbar, no less than 2 inches from the end of the wire. Tighten the green ground screw. B. Strip back the wire covering the 3 fixture wires as far as you need to. This will expose each fixture wire individually. Strip each end of 3 fixture wires. C. Use standard wire connectors (not included) to make all wire connections. Twist connectors until wires are tightly joined together.