Installation Sheet

For Style RDE1613AWN
Installation Guide #IS-RDE1613AWN
1of2
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(3)B10CandelabraBasebulbs60WMaximum,bulbnotincluded.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.MissingParts?Contactyouroriginalplaceof
purchase.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
2018 QuoizelInc.
visit us on-line at www.quoizel.com
Package Contents
A
Crossbar Assembly
x1
Fixture Body
x1
B
STEP 1 - Installing the Crossbar Assembly
A. Pass the supply wires from outlet box through the Crossbar
Assembly (A). Attach the Crossbar Assembly (A) to the Outlet Box
with the head of the Green Ground Screw facing you. Secure the
Crossbar Assembly (A) with Outlet Box Screws (not included).
Tighten until snug.
Supply Wires with
Ground Wire
Outlet Box Screws
(not included)
Outlet Box
A
Figure 1
STEP 2 Test Fitting Ceiling
Canopy to Crossbar Assembly
-
A.
eiling Canopy to the
ceiling
Remove mounting balls from
the Crossbar Assembly (A).
Fit the C
Crossbar Assembly (A) and
secure with mounting balls.
Note: The
should be snug against the
and the mounting
balls. If
Ceiling Canopy
not, adjust the length
of the nipple on the Crossbar
Assembly (A) by unscrewing
the preassembled hex nut
and lock washer and then
screwing the mounting
screws in or out of the
crossbar until the correct
length is achieved. Once the
Ceiling Canopy is secure,
remove the mounting ball and
Ceiling Canopy and proceed
to Step 3.
Mounting Screw
Hex Nut and
Lock Washer
Mounting Ball
A
Figure 2
ReleasedDate:2018-09-14
Ceiling Canopy
STEP 3 - Wire Connections
A.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
Figure 3
Green Ground Screw
on the Crossbar
White wire
from outlet box
White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
STEP 4 Install the Fixture-
A. Carefully tuck all wires into
the outlet box and position the
Ceiling Canopy over the outlet
box. Align the holes in the
ceiling canopy with the
mounting screws, then attach
the Ceiling Canopy using the
previously removed mounting
balls. Hand tighten until snug.
Figure 4
Mounting Screw
Mounting Ball
A
Ceiling Canopy
STEP 5 Install the Bulb-
A. Insert the bulb onto the socket
and screw snugly into place.
Figure 5
Bulb (not included)
C
Nipple Assembly
x1
D
Diffuser
x1