Installation Guide

1of2
Assembly Instruction Sheet #IS-RGE9011WT
For Style RGE9011WT
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2014 QuoizelInc.
November2014
Package Contents
C
Bulb
x1
A
Mounting
Screw
x3
B
Fixture
Hood
x1
ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters,wire strippers,electrical tape,safety glasses.
BulbRecommended: (1) MediumBase DecorativeFilament 60Wbulbs (provided),Maximum 150W,Alternatebulb (1)42W CFLMaximum.
EstimatedAssemblyTime:
Preparation:
30-45minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besureall partsare
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperatethefixture.Contact customerservice forreplacement
parts.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering November result.
STEP 1 Remove Package
Material out of
the Cage
-
A. Remove Fixture Hood
from top of the Cage by
unlocking Lock Balls and
Rubber Washers.
Remove Package
Material out of the Cage.
Lock Ball
Rubber
Washer
Package
Material
Cage
Fixture
Hood
STEP 2 Install Bulb-
A. This fixture uses standard bulb 60W
(supplied) with a standard screw
base. Maximum 150 watts.
B. Insert bulb and screw properly into
place.
C. Place Fixture Hood back onto Cage
and secure with Rubber Washers
and Lock Balls.
Figure 2
Bulb
Socket
Figure 1
Lock Ball
Rubber
Washer
Fixture
Hood
Cage
STEP 3 Drill Pilot Holes on Post-
A. Carefully fit the Post Fitter over the
end of the Post (not supplied), making
sure the Post Fitter is fully seated.
B. Mark the drill point for the (3) Mounting
Screws, using (3) Mounting Holes as
reference. After marking hole
locations, remove fixture from post
and drill 1/16” pilot holes for screws.
Post
Post Fitter
Figure 3
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Ground wire
from fixture
Figure 4
STEP 5 Attach Fixture Body to Post-
A. Coat the top 1” of the Post with Clear
Silicone Caulk (not supplied) and
position the Post Fitter onto the Post.
Be sure to seat it completely, aligning
the holes in the Fitter with the 1/16”
Pilot Holes drilled into the Post.
B. Secure the Fixture to Post with (3)
Mounting Screws.
Your fixture is now assembled and
ready to use. Enjoy!
Post
Fitter
Post
Figure 5
Mounting
Screw