Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(1)MediumBasebulb100WMaximum.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-SNN1909
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
For Styles SNN1909K, SNN1909PN and SNN1909W
2018 QuoizelInc.
ReleasedDate:2018-11-12
visit us on-line at www.quoizel.com
Package Contents
Crossbar
Assembly
x1
Ceiling Canopy
x1
Fixture Chain
x1
Quick Link
x2
A
Fixture Body
x1
B
C
D
E
Outlet Box Screw
x2
F
Wire Connector
x3
G
STEP 1 - Install the Crossbar Assembly to Outlet Box and Adjust
the length of the Nipple
A. Attach the Crossbar Assembly (A) to the Outlet Box with the head of
the Green Ground Screw facing you. Secure it with Outlet Box
Screws (F), tighten until snug
B. Adjust the hex nut and lock washer underside of the crossbar to the
middle of the nipple.
C. Remove the canopy lock ring from the canopy chain loop. Place the
Ceiling Canopy (D) over the canopy chain loop against the ceiling to
determine the correct position of the nipple. Thread the canopy lock
ring onto the canopy chain loop. Adjust the nipple to allow the Ceiling
Canopy (D) to rest against the ceiling when held in place by the
canopy lock ring.
D. Remove the canopy lock ring and the Ceiling Canopy (D). Tighten
the lock washer and the hex nut against the crossbar to secure in
place.
.
Hex Nut and
Lock Washer
Outlet Box
Green Ground Screw
Canopy Chain Loop
Canopy Lock Ring
Nipple
Figure 1
D
A
F
Approximately 8” of wire
extending from the Outlet Box.
E. Go to Step 3 for wire
connections and follow the
directions. Return to Step F in
this step when complete with
Step 3.
F. Raise the Ceiling Canopy (D)
and canopy lock ring up the
Fixture Chain (B) and over the
canopy chain loop. Tighten the
canopy lock ring onto the
canopy chain loop until tight.
Suggested chain length for
Ceiling height :
8’ ceiling : use 15 links of chain
and 2 quick links
9’ ceiling : use 26 links of chain
and 2 quick links
10’ ceiling : use 37 links of
chain and 2 quick links
Nipple
Fixture
Loop
Supply
Wires and
Ground Wire
Canopy
Chain Loop
Canopy
Lock Ring
C
B
D
C
Figure 2
STEP 2 - Install the Fixture Chain and Ceiling Canopy
A. Adjust the Fixture Chain (B) to your desired length by removing
links if needed. Put a cloth over the Fixture Chain (B) to protect the
finish.
B. Pull the supply wires through the Fixture Chain (B) alternating links.
After the wires are through the Fixture Chain (B), pull the Supply
Wires and the Ground Wire through the canopy lock ring and the
Ceiling Canopy (D) in order.
C. Attach one end of the Fixture Chain (B) to the fixture loop with one
Quick Link (C). Lift the fixture and Fixture Chain (B) up and attach
the other end of the Fixture Chain (B) onto the canopy chain loop
with another Quick Link (C). The fixture will now hang safely.
D. Feed the Supply Wires and Ground Wire through the canopy chain
loop and nipple into the outlet box. Cut the wires leaving