Installation Guide

1of1
Assembly Instruction Sheet #IS-TF2600FVA
For Style TF2600FVA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700
or visit us on-line at www.quoizel.com
2015 Quoizel Inc.
December2015
A. Place the Base, the Flat Washer and
the Spring Washer over the nipple on
the bottom center of the Decorative
Column in turn. Secure by threading
Finial
x1
Bulb (not
included)
TF2600FVA
NOTE:
ALL DIMENSIONS ARE
ROUNDED UP TO THE
NEAREST 1/4"
(3) 100W
Bulbs
(Not Supplied)
Medium
Base
Decorative
Column
x1
Pleasegoto forproduct cleaningtips. Goto the selection.
(3)Medium Base100W bulbMaximum,Alternatebulb (3)23W CFLMaximum.
15-20minutes
Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are
present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement
parts.
www.quoizel.com Care+ Maintenance
LightSource:
Estimated Assembly Time:
Preparation:
Tools Required: None.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
Shade
x1
Flat Washer
x1
Big
Knurled
Nut x 1
Small Knurled
Nut x 1
Check
Ring
x1
Spacer Tube
x1
Nipple with
Hex Nut
x1
Socket
Assembly
x1
Rod
x1
Rod with
Nipple
x1
Cord
Hex
Coupling
PART NUMBER REPLACEMENT PART
QTY.
NO.
1
2
12600FVATF
BASE
1
G12712SH SHADE
1
FINISH: VALIANT BRONZE
23.5” Dia.
9.75”
61”
12” Dia.
2
1
Base
x1
Flat Washer
x1
Spring Washer
x1
Thumb Nut
x1
the Thumb Nut onto the nipple.
Hand tighten until snug.
B. Thread the Socket Assembly,
the Rod, the Rod with Nipple and
the Decorative Column together
as shown. Pull the cord from the
Base as you assemble the parts
together to remove the excess
cord between parts. Hand
tighten until snug.
C. Thread the Hex Nut end of the
Nipple with Hex Nut into the hex
coupling on the top center of the
Socket Assembly. By using
pliers, thread the Hex Nut
against the hex coupling and
hand tighten until snug.
D. Pass the Spacer Tube and the
Check Ring over the top end of
the Nipple with Hex Nut and
secure with the Small Knurled
Nut.
E. Thread the Big Knurled Nut onto
Nipple and adjust it to proper
location for rest components.
Place the Flat Washer and the
Shade over the top end of the
Nipple and secure with the
Finial. Hand tighten until
snug.
F. This fixture uses standard
bulb with medium base .
Maximum 100 watts. Insert
bulb and screw snugly into
place.
Your fixture is now
assembled and ready to
use. Enjoy!