Installation Manual

ManualsBrandsQuoizel ManualsFixed Track Lighting KitsTFIK1404VA

1of2

Assembly Instruction Sheet #IS-TFIK1404VA

For Style TFIK1404VA

6 CORPORATE PARKWAY

GOOSE CREEK SC 29445

www quoizel com

Thank you for purchasing a Quoizel product.

Need assistance with parts or assembly? Call Quoizel customer service at 1-631-273-2700

or visit us on-line at www.quoizel.com

2015 QuoizelInc.

September2015

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Care of Tiffany Style Shade

A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is

too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.

For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.

If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or

mineral oil applied directly to oxidized areas and the soldered area will return to like new.

Package Contents

Crossbar

Lock Washer

Hex Nut

Nipple

Shade

Lock Ball

Fixture Body

Steel Collar

Socket Collar

STEP 1 Install Crossbar-

A. A)Attach the Crossbar ( to the Outlet Box with the head of the Green

Ground Screw facing you. Secure it with Outlet Box Screws (not

included) Tighten until snug..

Figure 1

Outlet Box

Outlet Box Screw

(not included)

Green Ground

Screw

STEP 2 Install Nipple and Fixture Body-

* Pliers is required for this step.

A. Thread Hex Nut (C) to the middle of the Nipple (D). Place Lock

Washer (B) over the Nipple (D) and then thread the Nipple (D) into

the Crossbar (A) until the Nipple (D) is about 0.375” above the

Crossbar (A).

B. Place the Fixture Body (I) over the Nipple (D) against the ceiling to

determine the correct position of the Nipple (D). Thread the Lock

Ball (E) onto the Nipple (D). Adjust the Nipple (D) to allow the

Fixture Body (I) to rest against the ceiling when held in place by the

Lock Ball (E).

C. Remove the Lock Ball (E) and the Fixture Body (I). Tighten the Hex

Nut (C) against the Crossbar (A) to secure in place.

Figure 2

Pleasegoto forproduct cleaningtips. Goto the selection.

(4)A19MediumBase 100WMaximum,Alternatebulb (4)23W CFL.

30-45minutes

Identifyand inspectall partsbefore beginninginstallation. Checkpackage contentlist anddiagrams belowto besure allparts are

present.If anyparts aremissing ordamaged, donot attemptto assemble,install, oroperate thefixture. Contactcustomer servicefor replacement

parts.

www.quoizel.com Care+ Maintenance

LightSource:

EstimatedAssemblyTime:

Preparation:

ToolsRequired:Flathead screwdriver,Phillips screwdriver,pliers, wirecutters, wirestrippers, electricaltape, safetyglasses.

STEP 3 Attach Lanyard-

A. The purpose of the lanyard is to provide the installer a means to

support the fixture from the junction box while connecting the

electrical wires. This enables the fixture to hang from the junction

box and your hands are free to make the wire connections.

B. Turn the Button Stop so it may be inserted into the crossbar slot.

Figure 3

Slot

Button Stop

Lanyard

Summary of content (2 pages)

PAGE 1
Assembly Instruction Sheet #IS-TFIK1404VA For Style TFIK1404VA 6 CORPORATE PARKWAY GOOSE CREEK , SC . 29445 www . quoizel . com Please go to www.quoizel.com for product cleaning tips. Go to the Care + Maintenance selection. Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (4) A19 Medium Base 100W Maximum, Alternate bulb (4) 23W CFL.
PAGE 2
(Step 3 Continued) TFIK1404VA Make sure the Button Stop is completely inside the crossbar. Slowly release the fixture to make sure it is supported by the Button Stop. Proceed to the wiring steps. Once you are complete with the wiring there is nothing to do with Lanyard. The Lanyard will push into the junction box when the fixture is placed for final mounting. FINISH: VALIANT BRONZE 9.5” 4.5” STEP 4 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections.