Installation Guide

Pleasegoto forproductcleaningtips.Gotothe selection.
(2)A19MediumBase60WMaximum,alternatebulbs(2)13WCFL.
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care+Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-TFIK1611VA
For Style TFIK1611VA
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
2016 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
Package Contents
ReleasedDate:2016-06-08
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
Care of Tiffany Style Shade
A new tiffany lamp shade has an oil film applied to the shade that protects the tiffany shade from scratches during shipment. If the oil applied is
too heavy you can remove the excess oil film with a paper towel. Gently wipe away the excess oil.
For general cleaning of tiffany shades use a gentle lemon oil-based furniture polish applied to a soft cloth and wipe gently.
If a white powder appears on the soldered joints of the tiffany shade this is a normal oxidation process. Use a small amount of lemon oil or
mineral oil applied directly to oxidized areas and the soldered area will return to like new.
A
B
Shade
x1
C
Nipple with
Hex Nut 4”L
x1
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
Figure 1
Outlet Box
Outlet Box Screw
(not included)
Green Ground
Screw
STEP 1 Install Crossbar-
A. A)Attach the Crossbar ( to the Outlet Box with the head of the Green
Ground Screw facing you. Secure it with Outlet Box Screws (not
included) Tighten until snug..
STEP 2 Install Nipple and Hex Nuts-
* Pliers are required for this step.
A. Thread one Hex Nut (C) to the middle of Nipple (E). Place one Lock
Washer (B) over Nipple (E) and then thread Nipple (E) into Crossbar
(A) until the Nipple (E) is about 0.375” above Crossbar (A).
B. Place Ceiling Canopy (F), Flat Washer (D) and another Lock Washer
(B) over Nipple (E) against the ceiling to determine the correct
position of Nipple (E). Adjust Nipple (E) to allow Ceiling Canopy (F)
Figure 2
(Step 2 Continued)
to rest against the ceiling when held in place by Hex Coupling (G).
C. Remove Hex Coupling (G), one Lock Washer (B), Flat Washer (D)
D
Flat Washer
x1
Nipple
x1
E
Ceiling
Canopy
x1
F
Hex Coupling
x1
G
H
I
J
Finial
x1
A
A
B
C
E
C
G
F
B
D
STEP 3 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
White wire
from supply
White wire
from fixture
Black wire from
supply (or Red)
Black wire
from fixture
Ground wire
from supply
Figure 3
Ground wire
from fixture
and Ceiling Canopy (F).
Tighten Hex Nut (C) against
Crossbar (A) to secure in
place.
D. Thread another Hex Nut (C)
onto the end of Nipple (E) and
adjust it just enough so that
the inside surface of Ceiling
Canopy (F) rests against it.
You may have to trial fit
Ceiling Canopy (F) one more
times to insure this distance
also. This Hex Nut (C) is
needed here to prevent you
from crushing down the center
of Ceiling Canopy (F).