User's Manual
Table Of Contents
- Compliance
- Specifications
- Contents
- Troubleshooting
- Important Warnings
- Preface
- System Overview
- Uses for the Solution include
- Special Features include
- System Components
- Settings
- Viewing History
- To select a start and end date
- 1. Click Start Date arrow to display the Date Picker.
- 2. Select Start Date from the Date Picker.
- 3. Click End Date arrow to display a second Date Picker.
- 4. Select End Date from the Date Picker.
- 5. The number of records returned by the date range appears in the lower left corner.
- Clear and Export History
- To select a start and end date
- Seeker Installation
- To install the Seeker Software
- 1. Using a sync cable or cradle, connect your Pocket PC to the computer. For additional information, see the documentation that arrived with the Pocket PC.
- 2. Insert the Seeker software and documentation CD into the drive on the computer.
- 3. Double-click My Computer.
- 4. Navigate to the CD drive.
- 5. Double-click setup.exe.
- 6. Follow the instructions on the screen to finish the installation.
- Installing the RF Reader
- To install the Seeker Software
- Using Seeker Software
- To start the Seeker Software
- The Main Window
- Working Offline
- Tag Entry
- To associate a Tag with a resource
- 1. Tap Add. The Add Tag window appears.
- 2. In the Department box, select a Department ID.
- 3. In the Tag box, select a Tag ID.
- 4. In the Resource box, type the name for this resource.
- 5. In the Description box, type a description for this resource.
- 6. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 7. Select the bitmap to be used to represent the resource.
- 8. Tap OK, to save the Tag/resource association.
- Find Tags
- Low Battery Indicator
- Department ID
- To erase a Tag
- To write to a blank Tag
- To find a Tag using Department and Tag
- To find a Tag using Resource and Locations
- 1. In the Resource box, select the Resource associated with the Tag.
- 2. If applicable, select the Location from the Location box. The Locations are downloaded from the PinPoint Configurator Service.
- 3. Select the Beep checkbox, to hear the Tag beep. Select the Light checkbox to see the Tag flash.
- 4. Move the Range slider to the right to increase the range.
- 5. Click Find to start searching for Tags
- Progress Bar
- Tag Count
- Working Online
- Mobile Locating Solution
- User Guide
- Mounting Seeker Tags
- To apply the adhesive pad to the Tag
- To attach a Tag to a resource using an adhesive pad
- 1. Obtain the resource to which you want to apply the Tag. The resource surface should be clean, dry and free of condensed moisture.
- 2. Remove the adhesive plastic guard.
- 3. Firmly attach the Tag to the resource. Ideal application temperature range is 70˚F to 100˚F (21˚C to 38˚C).
- 4. Press firmly and hold for a couple of minutes to activate the pressure sensitive adhesive.
- To edit a Tag/resource association
- 1. In the Tag Entry list, select an item to edit.
- 2. Tap Edit.
- 3. In the Resource box, type the name for this resource.
- 4. In the Description box, type a description for this resource.
- 5. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 6. Select the bitmap to be used to represent the resource.
- 7. Tap OK, to save the changes.
- To delete a Tag/resource association
- To clean a Seeker Tag after use
- Mounting Seeker Tags
18
11
Find Tags
The Find Tags window appears in one of three
modes.
1. Working offline using Resource Names
You must select a resource to search for by
selecting its resource name from the Resource
box. Department searches can not be performed
when using the resource names.
To operate in this mode select the Use Resource
Names checkbox in the Settings window.
2. Working offline using Department and Tag
Select a Department and a Tag. In offline mode
the user can select a department and then “Any”
Tag or a specific Tag in the Tag List (see
illustration on top of page 12).
3. Working online using PinPoint Data
You select the location they are currently occupying and the Tag to find. When Tags
are received they are matched to a record in the local database. The database
information is used to provide additional details about the Tag and asset (see
illustration on bottom of page 12). Department searches can not be performed when
working online.
NOTE: In online mode, the locations and resources are retrieved from
the PinPoint Mobile Resource Manager. See the “Integrating with Mobile
Resource Manager” in this guide for details.
Department Entry
The Department Entry allows users to enter information about departments used
to group Tags.
To add Department information
1. Tap Add. The Add Department window appears.
2. In the Department box, select a Department ID.
3. In the Name box, type in the department name.
4. Tap OK, to save the department information.
To edit Department information
1. Select the department you wish to edit.
2. Tap Edit. The Edit Department window appears.
3. In the Name box, edit the department name.
4. Tap OK, to save the department information.
To delete Department information
1. Select the department you wish to edit.
2. Tap Edit. The Edit Department window appears.
3. In the Name box, edit the department name.
4. Tap OK, to save the department information.