User's Manual
Table Of Contents
- Compliance
- Specifications
- Contents
- Troubleshooting
- Important Warnings
- Preface
- System Overview
- Uses for the Solution include
- Special Features include
- System Components
- Settings
- Viewing History
- To select a start and end date
- 1. Click Start Date arrow to display the Date Picker.
- 2. Select Start Date from the Date Picker.
- 3. Click End Date arrow to display a second Date Picker.
- 4. Select End Date from the Date Picker.
- 5. The number of records returned by the date range appears in the lower left corner.
- Clear and Export History
- To select a start and end date
- Seeker Installation
- To install the Seeker Software
- 1. Using a sync cable or cradle, connect your Pocket PC to the computer. For additional information, see the documentation that arrived with the Pocket PC.
- 2. Insert the Seeker software and documentation CD into the drive on the computer.
- 3. Double-click My Computer.
- 4. Navigate to the CD drive.
- 5. Double-click setup.exe.
- 6. Follow the instructions on the screen to finish the installation.
- Installing the RF Reader
- To install the Seeker Software
- Using Seeker Software
- To start the Seeker Software
- The Main Window
- Working Offline
- Tag Entry
- To associate a Tag with a resource
- 1. Tap Add. The Add Tag window appears.
- 2. In the Department box, select a Department ID.
- 3. In the Tag box, select a Tag ID.
- 4. In the Resource box, type the name for this resource.
- 5. In the Description box, type a description for this resource.
- 6. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 7. Select the bitmap to be used to represent the resource.
- 8. Tap OK, to save the Tag/resource association.
- Find Tags
- Low Battery Indicator
- Department ID
- To erase a Tag
- To write to a blank Tag
- To find a Tag using Department and Tag
- To find a Tag using Resource and Locations
- 1. In the Resource box, select the Resource associated with the Tag.
- 2. If applicable, select the Location from the Location box. The Locations are downloaded from the PinPoint Configurator Service.
- 3. Select the Beep checkbox, to hear the Tag beep. Select the Light checkbox to see the Tag flash.
- 4. Move the Range slider to the right to increase the range.
- 5. Click Find to start searching for Tags
- Progress Bar
- Tag Count
- Working Online
- Mobile Locating Solution
- User Guide
- Mounting Seeker Tags
- To apply the adhesive pad to the Tag
- To attach a Tag to a resource using an adhesive pad
- 1. Obtain the resource to which you want to apply the Tag. The resource surface should be clean, dry and free of condensed moisture.
- 2. Remove the adhesive plastic guard.
- 3. Firmly attach the Tag to the resource. Ideal application temperature range is 70˚F to 100˚F (21˚C to 38˚C).
- 4. Press firmly and hold for a couple of minutes to activate the pressure sensitive adhesive.
- To edit a Tag/resource association
- 1. In the Tag Entry list, select an item to edit.
- 2. Tap Edit.
- 3. In the Resource box, type the name for this resource.
- 4. In the Description box, type a description for this resource.
- 5. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 6. Select the bitmap to be used to represent the resource.
- 7. Tap OK, to save the changes.
- To delete a Tag/resource association
- To clean a Seeker Tag after use
- Mounting Seeker Tags
22
7
System Components
The following components comprise the Seeker Mobile Locating Solution.
Ta g s
Tags are small and can be attached to resources using the
adhesive tape that is included with them. Tags can also be
mounted with a lanyards (or zip strip) through the lanyard
clip opening at the top of the Tag.
When a Tag is found by the Pocket PC, it responds with its
unique Tag ID and a status message that indicates its battery
condition. Tags can be programmed to beep and flash a light
which allows users to gain a rough indication of where the Tag is located.
RF Reader with External Antenna
The Compact Flash (CF) RF Reader with external
Antenna includes the receiver circuitry and the
microprocessor. The microprocessor helps in
decoding the Tag signals to obtain the Department ID,
Tag ID, and the status of the Tag. The information is
transferred to the Pocket PC using standard CF
protocols.
Pocket PC
The Pocket PC includes the Microsoft Pocket PC
Operating System. The Pocket PC supports the
Compact Flash standard CF+/Type II for the
addition of the RF Reader.
Software
The software and documentation are provided on a
CD-ROM.
Settings
About Tab
Seeker software information is located on the About tab in the Setting window. It
displays the application version and operating system version.
To display Seeker software information
1. Tap Settings from the Main Window.
2. Select the About Tab.
HELPFUL HINTS
Be sure to have this information
available when contacting the RF
Technologies Customer Support Team.