User's Manual
Table Of Contents
- Compliance
- Specifications
- Contents
- Troubleshooting
- Important Warnings
- Preface
- System Overview
- Uses for the Solution include
- Special Features include
- System Components
- Settings
- Viewing History
- To select a start and end date
- 1. Click Start Date arrow to display the Date Picker.
- 2. Select Start Date from the Date Picker.
- 3. Click End Date arrow to display a second Date Picker.
- 4. Select End Date from the Date Picker.
- 5. The number of records returned by the date range appears in the lower left corner.
- Clear and Export History
- To select a start and end date
- Seeker Installation
- To install the Seeker Software
- 1. Using a sync cable or cradle, connect your Pocket PC to the computer. For additional information, see the documentation that arrived with the Pocket PC.
- 2. Insert the Seeker software and documentation CD into the drive on the computer.
- 3. Double-click My Computer.
- 4. Navigate to the CD drive.
- 5. Double-click setup.exe.
- 6. Follow the instructions on the screen to finish the installation.
- Installing the RF Reader
- To install the Seeker Software
- Using Seeker Software
- To start the Seeker Software
- The Main Window
- Working Offline
- Tag Entry
- To associate a Tag with a resource
- 1. Tap Add. The Add Tag window appears.
- 2. In the Department box, select a Department ID.
- 3. In the Tag box, select a Tag ID.
- 4. In the Resource box, type the name for this resource.
- 5. In the Description box, type a description for this resource.
- 6. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 7. Select the bitmap to be used to represent the resource.
- 8. Tap OK, to save the Tag/resource association.
- Find Tags
- Low Battery Indicator
- Department ID
- To erase a Tag
- To write to a blank Tag
- To find a Tag using Department and Tag
- To find a Tag using Resource and Locations
- 1. In the Resource box, select the Resource associated with the Tag.
- 2. If applicable, select the Location from the Location box. The Locations are downloaded from the PinPoint Configurator Service.
- 3. Select the Beep checkbox, to hear the Tag beep. Select the Light checkbox to see the Tag flash.
- 4. Move the Range slider to the right to increase the range.
- 5. Click Find to start searching for Tags
- Progress Bar
- Tag Count
- Working Online
- Mobile Locating Solution
- User Guide
- Mounting Seeker Tags
- To apply the adhesive pad to the Tag
- To attach a Tag to a resource using an adhesive pad
- 1. Obtain the resource to which you want to apply the Tag. The resource surface should be clean, dry and free of condensed moisture.
- 2. Remove the adhesive plastic guard.
- 3. Firmly attach the Tag to the resource. Ideal application temperature range is 70˚F to 100˚F (21˚C to 38˚C).
- 4. Press firmly and hold for a couple of minutes to activate the pressure sensitive adhesive.
- To edit a Tag/resource association
- 1. In the Tag Entry list, select an item to edit.
- 2. Tap Edit.
- 3. In the Resource box, type the name for this resource.
- 4. In the Description box, type a description for this resource.
- 5. Next to the Image field, tap the ellipses (…) box to link an image to the entry.
- 6. Select the bitmap to be used to represent the resource.
- 7. Tap OK, to save the changes.
- To delete a Tag/resource association
- To clean a Seeker Tag after use
- Mounting Seeker Tags
12
17
Selecting a Tag to Find
To find a Tag using Department and Tag
1. In the Department box, select a Department
ID.
2. In the Ta g box, select a Tag ID.
3. Select the Beep checkbox, to hear the Tag
beep. Select the Light checkbox to see the
Tag fl as h.
4. Move the Range slider to the right to
increase the range.
Adjusting the Range increases and decreases
the range at which Tags respond. A lower
setting decreases the range that Tags can be
read from the RF Reader.
5. Click Find to start searching for Tags.
To find a Tag using Resource and Locations
1. In the Resource box, select the Resource
associated with the Tag.
2. If applicable, select the Location from the
Location box. The Locations are
downloaded from the PinPoint
Configurator Service.
3. Select the Beep checkbox, to hear the Tag
beep. Select the Light checkbox to see the
Tag fl as h.
4. Move the Range slider to the right to
increase the range.
Adjusting the Range increases and
decreases the range at which Tags respond.
A lower setting decreases the range that
Tags can be read from the RF Reader.
5. Click Find to start searching for Tags
To edit a Tag/resource association
1. In the Tag Entry list, select an item to edit.
2. Tap Edit.
The Edit Tag window appears.
3. In the Resource box, type the name for this
resource.
4. In the Description box, type a description for this
resource.
5. Next to the Image field, tap the ellipses (…) box to
link an image to the entry.
6. Select the bitmap to be used to represent the
resource.
7. Tap OK, to save the changes.
To delete a Tag/resource association
1. In the Tag Entry list, select an item to delete.
2. Tap Delete.
3. The item disappears from the list.
To clean a Seeker Tag after use
1. If necessary, remove the Seeker Tag from the resource.
You can clean the Tag on the resource if you prefer.
2. Wet a cotton swab or paper towel with Isopropyl Alcohol.
3. Cleanse the Seeker Tag.
4. Cleanse the surface of the resource.
5. Let the Seeker Tag and the resource surface dry before reapplying the Seeker Tag with the
adhesive pad.
NOTE: It is best to keep the size of the bitmap or jpeg as small as possi-
ble (maximum of 12Kb). Large images may not appear.