Owner`s manual

ManualsBrandsR.H. Peterson ManualsLawn and Garden882 Vented Series

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746 Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLATION &

OWNER’S MANUAL

WARNING: If the information in this manual

is not followed exactly, a ﬁ re or explosion may

result causing property damage, personal

injury or loss of life.

- Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

- A propane cylinder not connected for use

shall not be stored in the vicinity of this or

any other appliance.

DANGER

If you smell gas:

1. Shut off gas to the appliance.

2. Extinguish any open ﬂ ame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or ﬁ re department.

Installation and service must be performed by

an NFI Certiﬁ ed or other qualiﬁ ed professional

installer, service agency, or gas supplier.

F14-023

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause property

damage, personal injury, or loss of life. Read

the installation, operating and maintenance

instructions thoroughly before installing or

servicing this equipment.

CODE AND SUPPLY REQUIREMENTS:

The gas installation must conform with local codes

and ordinances, or, in the absence of local codes,

with the latest National Fuel Gas Code, ANSI Z223.1.

The R.H.P. gas appliance is designed as an

attended appliance. Adults must be present when

the unit is operating. DO NOT leave the unit burning

when unattended. If the product is left burning

unattended, it may cause damage or serious injury.

INSTALLER & CONSUMER: These instructions MUST

be retained with this unit for future reference.

Important: Read these instructions carefully

before starting installation of the unit.

IMPORTANT

For safe operation and proper performance of

this product and to comply with certification,

listings, and building code acceptances, use ONLY

Robert H. Peterson (R.H.P.) controls, parts, and

accessories that have been speciﬁ cally listed or

certiﬁ ed for use with this ﬁ replace. Use of other

controls, parts, or accessories is prohibited and

will void all warranties, certiﬁ cations, listings, and

building code approvals, and may cause property

damage, personal injury, and loss of life.

Complies with:

ANSI Z21.97/CSA 2.41 for

outdoor decorative gas

appliances

(when installed with select

R.H.P. Vented/Unvented

Gas Appliances)

WARNING: For Outdoor Use Only

DANGER

CARBON MONOXIDE HAZARD

A vented gas appliance can produce

carbon monoxide which has no odor.

Using it in an enclosed space can

kill you.

Never use the appliance in an

enclosed space such as a camper,

tent, car, or home.

REV 1 - 1411101150

L-H2-010

CORDOVA (STANDARD, REDUCED, GRAND) OUTDOOR FIREPLACES

Vented Series: 022, 023, 882

Unvented Series: 122, 123,182

022

series

shown

Summary of content (26 pages)

PAGE 1
INSTALLATION & OWNER’S MANUAL Vented Series: 022, 023, 882 Unvented Series: 122, 123,182 Complies with: ANSI Z21.97/CSA 2.41 for outdoor decorative gas appliances (when installed with select R.H.P. Vented/Unvented Gas Appliances) 022 series shown F14-023 WARNING: For Outdoor Use Only CORDOVA (STANDARD, REDUCED, GRAND) OUTDOOR FIREPLACES INSTALLER & CONSUMER: These instructions MUST be retained with this unit for future reference.
PAGE 2
INSTALLATION ET MODE D'EMPLOI Ventilé Série: 022, 023, 882 Non Ventilé Série: 122, 123,182 Conforme à: ANSI Z21.97/CSA 2.41 pour l'extérieur des appareils à gaz décoratifs (lorsqu'il est installé avec sélection R.H.P. Ventilé / non ventilé les appareils à gaz) Série 022 montré F14-023 AVERTISSEMENT: Pour l'usage extérieur seulement CORDOVA (STANDARD, REDUCED, GRAND) CHEMINÉES D'EXTÉRIEUR d'INSTALLATEUR; CONSOMMATEUR: Ces instructions DOIVENT être maintenues avec cet appareil pour la future référence.
PAGE 3
TABLE OF CONTENTS GETTING STARTED PRE-INSTALLATION AND PREPARATION SAFETY GUIDELINES .....................................................4 INSTALLATION SAFETY GUIDELINES ...................................................................................................5 OPERATING THE UNIT SAFELY AND CORRECTLY .............................................................................5 SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS ..........................................................7 NOTES PAGE ..
PAGE 4
PRE-INSTALLATION AND PREPARATION SAFETY GUIDELINES This fireplace is designed to be installed with select R.H.P. vented/unvented gas appliances. The following 3 sections of warnings apply to this complete setup type: A. Before installing this unit, check the MINIMUM CLEARANCE TO COMBUSTIBLES section to ensure that the surrounding area is properly sized for the installation. B. The unit is for outdoor use only.
PAGE 5
INSTALLATION SAFETY GUIDELINES A. Installation and repair should be done by a qualified professional service technician. The gas appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required as necessary. It is imperative that control compartment, burners and circulating air passageways of the fireplace and/or appliance are kept clean. B. Carefully inspect for shipping damage. If any parts are damaged, call the dealer. C.
PAGE 6
UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE IMPORTANT POUR VOTRE SÛRETÉ LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE. En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements. LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.
PAGE 7
SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS IMPORTANT FOR YOUR SAFETY READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER. When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed. FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION. The use of pliers or a wrench should not be necessary. Only cylinders marked “propane” may be used. CYLINDER/CONNECTOR REQUIREMENTS a.
PAGE 8
NOTES PAGE Please use this page to record any information that you may want to have at hand.
PAGE 9
SPECIFICATIONS AND DIMENSIONS Fireplace Style Dimensions Weight / Pieces Cordova Fireplace (022 & 122) * 76" w x 41" d x 95" h 1700 lbs / 11 pcs Reduced Cordova Fireplace (023 & 123) * 76" w x 41" d x 82" h 1600 lbs / 10 pcs Grand Cordova Fireplace (882 & 182) † 110" w x 41" d x 95" h 1900 lbs / 13 pcs * Dimensions, Weight, & Pieces listed based upon a standard 16" Rectangle Bullnose Hearth. † Dimensions, Weight, & Pieces listed based upon an 110" Rectangle Extended Bullnose Hearth.
PAGE 10
SPECIFICATIONS AND DIMENSIONS (cont.) Hearth Style Dimensions * 16" Rectangle Bullnose Hearth 76" w x 41" d x 16" h 4" Rectangle Bullnose Hearth 76" w x 41" d x 4" h 110" Rectangle Extended Bullnose Hearth 110" w x 41" d x 16" h 144" Rectangle Extended Bullnose Hearth 144" w x 41" d x 16" h 110" w x 56 1/2" d x 16" h 110" Radiused Bullnose Hearth * See previous page for 2" Recess Option information.
PAGE 11
SPECIFICATIONS AND DIMENSIONS (cont.) This fireplace is designed to be installed with an R.H.P. vented/unvented gas appliance. Below is a list of the options available for each fireplace type. The gas appliance is purchased separately. Contact your local American Fyre Designs dealer when ordering.
PAGE 12
MINIMUM CLEARANCES TO COMBUSTIBLES The dimensions shown below are MINIMUM CLEARANCES to maintain when you install the unit. ALL CLEARANCES AND INFORMATION STATED HERE MUST BE MAINTAINED AND FOLLOWED. Dimension Vented Fireplace Unvented Fireplace Description A. Side clearance (from hearth extension to combustible construction) 6" 6" B. Clearance above unit N/A 36" C. Clearance below unit 0" 0" 36" 36" 6" 6" Front clearance (from hearth extension to combustible construction) D. E.
PAGE 13
PARTS LIST • Your fireplace is packaged onto 1 pallet. • R.H.P. gas appliances are purchased and packaged separately. Various models are available. • R.H.P. gas appliances and replacement parts can be ordered from your local American Fyre Designs dealer. • Select models are illustrated (your model may vary) IMPORTANT COMPONENTS Remove all packing material (including any protective coatings) and discard prior to use.
PAGE 14
PARTS LIST (cont.) Item Description Qty. IDENTIFICATION PARTS LIST Grand Cordova (882, 182) 1. or or Hearth assembly - 110" Rectangle Extended Bullnose Hearth assembly - 144" Rectangle Extended Bullnose * Hearth assembly - 110" Radiused Bullnose * 1 1 1 2. or Firebox liners - Vented (4 pc set) Firebox liners - Unvented (5 pc set) * 1 1 3. Body - Base 1 4. Body - Middle 1 5. Body - Top 1 6. or Chimney - Vented Chimney - Unvented * 1 1 7. Side wall - Front 2 8.
PAGE 15
IMPORTANT SAFETY INFORMATION BE CAREFUL If not installed and used correctly per these instructions, this product can cause serious injury. CAUTION: Installation and maintenance must be done by an NFI Certified or other qualified professional service technician. Read these instructions before installing this fireplace and the R.H.P. gas appliance. Be sure you understand all safety precautions and warnings contained in this manual and the appliance owner's manual. A. FOR OUTDOOR USE ONLY. B.
PAGE 16
FIREPLACE INSTALLATION (cont.) FIREPLACE ASSEMBLY - OVERVIEW CAUTION: Fireplace components are heavy. CAREFULLY handle all components during assembly. • Fig. 16-1 provides an overall orientation and bolt assembly detail for the Cordova fireplace. (16" Rectangle Bullnose Hearth shown. Assembly may slightly vary depending on model and hearth selected.) • The Reduced Cordova & Grand Cordova assemble in the same manner.
PAGE 17
FIREPLACE INSTALLATION (cont.) FIREPLACE ASSEMBLY - STEP BY STEP See Parts List for large hardware kit qty. for hearth chosen CAUTION: F i r e p l a c e c o m p o n e n t s a r e h e a v y. CAREFULLY handle all components during assembly. Note: A Cordova Fireplace with a 16" Rectangle Bullnose Hearth is depicted here. Your assembly may slightly vary depending on model and hearth selected. Hearth and Base Body 1.
PAGE 18
FIREPLACE INSTALLATION (cont.) Middle Body 1. Place the middle body piece on top of the base body piece. Carefully align the pilot holes, and repeat the hardware installation process (large hardware kits). See Fig. 18-1. Hardware: Large Bolts x 4 Nuts x 4 Washers x 8 2. Return to the base body hardware and completely tighten. For Cordova and Reduced Cordova proceed to the LINERS, TOP BODY, & CHIMNEY section. For Grand Cordova models, continue on to the following section.
PAGE 19
FIREPLACE INSTALLATION (cont.) Liners, Top Body, & Chimney 1. Install the firebox liners into the interior of the firebox in the order shown in Fig. 19-1. Unvented fireplaces contain a liner for the top of the firebox. D • The rear liner has grooves to assist in placement. • Be sure to pull the flex connector inside of the fireplace body through the liner and into the open interior of the firebox (for later R.H.P. burner installation).
PAGE 20
BURNER INSTALLATION BURNER INSTALLATION GUIDELINES This fireplace is designed to be installed with an R.H.P. vented/unvented gas appliance. The gas appliance is purchased separately. Follow all owner's manuals included with the appliance and decorative media to complete installation. Note: The gas appliance will come equipped with a flex connector. Remove that connector, and connect the existing fireplace flex connector to the appliance. Make sure to tighten every joint securely.
PAGE 21
OPTIONAL ACCESSORIES OPTIONAL GFRC CHIMNEY RAIN VENT CAP An optional GFRC chimney rain vent cap is available to protect your unit from the rain. Contact your local dealer for ordering information. To place the cap, allow the unit to cool completely, then place as shown in Fig. 21-1. The cap can be in place during operation. OPTIONAL SCROLL SCREEN An optional scroll screen is available to protect your unit and to provide a decorative addition. Contact your local dealer for ordering information.
PAGE 22
DIRECTIVES DE L'ÉCLAIRAGE POUR VOTRE SÉCURITÉ, LIRE AVANT D'ALLUMER AVERTISSEMENT: SI VOUS NE SUIVEZ PAS CES INSTRUCTIONS À LA LETTRE, UN INCENDIE OU UNE EXPLOSION POURRAIENT S'ENSUIVRE, CAUSANT DES DOMMAGES MATÉRIELS, DES BLESSURES OU DES PERTES DE VIE. A. AVANT D'ALLUMER, sentez tout autour de l'unité de surface pour le gaz. Assurez-vous de sentir près du plancher, car certains gaz sont plus lourds que l'air et se déposent sur le sol. B. QUE FAIRE SI UNE ODEUR DE GAZ 1. Coupez le gaz à l'appareil. 2.
PAGE 23
LIGHTING GUIDELINES FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY, A FIRE OR EXPLOSION MAY RESULT, CAUSING PROPERTY DAMAGE, PERSONAL INJURY, OR LOSS OF LIFE. A. BEFORE LIGHTING, smell all around the unit area for gas. Be sure to smell next to the floor, because some gas is heavier than air and will settle on the floor. B. WHAT TO DO IF YOU SMELL GAS 1. Shut off the gas to the appliance. 2. Extinguish any open flame. 3.
PAGE 24
SERVICING AND CLEANING Each installation site for any unit presents its own unique combustion environment. Specific factors such as weather, wind currents, yard debris, altitude, drafts, the size of the surrounding area, all have an influence on the proper operation of the gas appliance.
PAGE 25
SERVICING AND CLEANING (cont.) CONCRETE CARE As with any surface, concrete components require regular maintenance and care. Certain guidelines must be followed to preserve the concrete's appearance and structural integrity. • Scratches may occur due to usage. To minimize, avoid striking or dragging heavy, rough, or sharp objects across the unit. • Spotting and hairline cracks may occur due to nature of product and are not considered a manufacturing defect.
PAGE 26
WARRANTY AMERICAN FYRE DESIGNS BY R. H. PETERSON CO. LIMITED WARRANTY Robert H. Peterson Co. (“RHP”) warrants your American Fire Designs product to be free from defects in material and workmanship. American Fyre Designs (“AFD”) exterior fireplaces, BBQ islands, fire tables, fire urns, fire pits, Fire Falls, Fire Walls, gas logs, and burner components (“products”) are warranted for THREE (3) YEARS. All AFD valves, electrical components, and controls are warranted for ONE (1) YEAR (excluding batteries).