Owner`s manual

ManualsBrandsR.H. Peterson ManualsBurnerG46-30-15P

REV 5 - 0707261445

No.L-A2-21507

Models

G46-18/20-01(M)(P)

G46-18/20-11(M)(P)

G46-18/20-15(M)(P)

G46-18/20(P)

G46-24-01(M)(P)

G46-24-11(M)(P)

G46-24-15(M)(P)

G46-24(P)

G46-30-01(M)(P)

G46-30-11(M)(P)

G46-30-15(M)(P)

G46-30(P)

C.S.A. CERTIFIED

GLOWING EMBERS

GAS FIREPLACE

LOG SET

Owner’s

Manual

ROBERT H. PETERSON CO.

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue • City of Industry, CA 91746

G46 BURNER SERIES

Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier from

a neighbor’s phone and follow the gas

supplier’s instructions.

• If you cannot reach the gas supplier,

call the ﬁ re department.

WARNING

If the information in this manual is not followed

exactly, a ﬁ re or explosion may result, causing

property damage, personal injury, or loss of life.

Installation and service must be

performed by an NFI Certiﬁ ed or other

qualiﬁ ed professional installer, service

agency, or the gas supplier.

Important: Read these instructions carefully

before starting installation of the

log set.

The Peterson Real-Fyre

gas log set is to be installed

only in a solid-fuel-burning ﬁ replace with a working ﬂ ue

constructed of noncombustible material. Solid fuels

shall not be burned in a ﬁ replace where this gas log

set is installed. The installation, including provisions

for combustion, ventilation air, and required minimum

permanent vent opening, must conform with the National

Fuel Gas Code (ANSI Z223.1/NFPA 54) and applicable

local building codes. In Canada, the installation must

conform with the Natural Gas and Propane Storage

and Handling Installation Code (CSA-B-149.1). A

damper stop clamp is included to maintain the minimum

permanent vent opening and to prevent full closure of

the damper blade. The chimney damper must be ﬁ xed

fully opened when burning this log set. This log set is

designed to burn with yellow ﬂ ames; thus, adequate

ventilation is absolutely necessary.

INSTALLER & CONSUMER

These instructions MUST be retained

with this appliance.

Important: To comply with certiﬁ cation, listings, and building code acceptances, and for safe operation and

proper performance of this log set, use ONLY Peterson Real-Fyre

parts and accessories. Use

of other controls, parts, or accessories that are not approved for use with Real-Fyre

gas log

sets is prohibited and will void all warranties, certiﬁ cations, listings, and building code approvals,

and may cause property damage, personal injury, or loss of life.

Summary of content (32 pages)

PAGE 1
ROBERT H. PETERSON CO. ® Models G46-18/20-01(M)(P) G46-18/20-11(M)(P) G46-18/20-15(M)(P) G46-18/20(P) Owner’s Manual C.S.A. CERTIFIED GLOWING EMBERS GAS FIREPLACE LOG SET G46-24-01(M)(P) G46-24-11(M)(P) G46-24-15(M)(P) G46-24(P) G46-30-01(M)(P) G46-30-11(M)(P) G46-30-15(M)(P) G46-30(P) G46 BURNER SERIES Important: WARNING If the information in this manual is not followed exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life.
PAGE 2
ROBERT H. PETERSON CO. ® Models G46-18/20-01(M)(P) G46-30-01(M)(P) G46-18/20-11(M)(P) G46-30-11(M)(P) G46-18/20-15(M)(P) G46-30-15(M)(P) G46-18/20(M)(P) G46-30(M)(P) MANUEL OWNERS C.S.A.
PAGE 3
TABLE OF CONTENTS PARTS LIST (REMOTE UNITS) PARTS LIST (MANUAL UNIT) SAFETY CONTROL SYSTEM FOR G46 MANUAL SAFETY CONTROL SYSTEM FOR G46-11(M)(P) SAFETY CONTROL SYSTEM FOR G46-01(M)(P) SAFETY CONTROL SYSTEM FOR G46-15(M)(P) LOG SET NOTES PAGE PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY IMPORTANT INFORMATION DAMPER STOP CLAMP INSTRUCTIONS INSTALLING THE GAS LOG SET DAMPER CLAMP INSTRUCTIONS CONNECTING THE IGNITION PACK TO THE G46-01(M)(P) VALVE INSTALLING OR REPLACING BATTERIES FOR IGNITION MODULE PACK
PAGE 4
PARTS LIST (REMOTE UNITS) Log styles, sizes, and parts will vary depending upon the G46 Series model ordered. When ordering replacement parts, be sure to indicate your log set model. Item no. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. or 13. or 14. 15. 16. 17. Note: Only the logs for the WO-24 Woodland Oak 24" set are illustrated and listed below.
PAGE 5
PARTS LIST (MANUAL UNIT) Log styles, sizes, and parts will vary depending upon the G46 Series model ordered. When ordering replacement parts, be sure to indicate your log set model. Note: Only the logs for the WO-24 Woodland Oak 24" set are illustrated and listed below. 5 1 6 2 3 4 Item no. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. or 13. or 14. 15. 16. 17.
PAGE 6
SAFETY CONTROL SYSTEM FOR G46 MANUAL Pilot assembly (rear view) Ceramic electrode Location of orifice 19 Pilot assembly Item no. 17. 18. or 19. 20. 21. 22. 20 22 Description Safety control valve Pressure regulator (natural gas) Pressure regulator (propane gas) Handle assembly Pilot assembly Ceramic electrode Adapter elbow 17 18 G46 burner showing valve layout under heatshield (rear view) DO NOT REMOVE HEATSHIELD SAFETY CONTROL SYSTEM FOR G46-11(M)(P) 23 24 Item no. 23. 24.
PAGE 7
SAFETY CONTROL SYSTEM FOR G46-01(M)(P) 26 25 Item no. 25. 26. G46 burner showing remote-control valve layout under heatshield Description Safety control valve Pilot assembly DO NOT REMOVE HEATSHIELD SAFETY CONTROL SYSTEM FOR G46-15(M)(P) 28 Item no. 27. 28.
PAGE 8
LOG SET NOTES PAGE Please use this page to record any information about your log set that you may want to have at hand. REV 5 - 0707261445 8 No.
PAGE 9
PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY CAUTION: Installation and repair must be done by an NFI Certified or other qualified professional installer. Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand all safety precautions and warnings contained in this manual. A. This appliance is designed as an attended appliance. Adults must be present when this gas appliance is operating.
PAGE 10
SÛRETÉ DE PRÉINSTALLATION ET DE PRÉPARATION DE CHEMINÉE ATTENTION: L’installation et la réparation doivent être faites par un NFI certifié ou autre qualifié, installateur professionnel. Installateur: Lisez soigneusement ces instructions avant d’installer ce système de brûleur à gaz. Soyez sûr que vous comprenez tous les mesures de sécurité et avertissements contenus en ce manuel. A. Cet appareil est conçu comme appareil occupé. Les adultes doivent être présent quand cet appareil de gaz fonctionne.
PAGE 11
IMPORTANT INFORMATION Do not use this log set if any part has been underwater. Immediately call a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater. The appliance and its individual shutoff valve must be disconnected from the gas-supply piping system when testing the system at test pressures in excess of ½ psig. This is accomplished by closing the gassupply line valve.
PAGE 12
DAMPER STOP CLAMP INSTRUCTIONS DAMPER CLAMP INSTRUCTIONS The damper clamp with hex bolt (Fig. 12-1) is provided as a means to prevent full closure of the damper blade. The clamp is easily attached to most damper blades with pliers or a wrench, and must be permanently installed. The clamp is designed to prevent accidental closure of the damper when installed as illustrated (Fig. 12-2 & Fig. 12-3).
PAGE 13
INSTALLING THE GAS LOG SET (Cont.) Note: Refer to the PARTS LIST when following these instructions. CAUTION: Turn off the gas to the fireplace before beginning this procedure. 1. The burner gas inlet is located in front of the gas valve (Fig. 10-4). Use Teflon tape or pipe compound on all pipe thread male connections, except where brass to brass. FOR THE G46 AUTOMATIC MILLIVOLT VALVE Attach the connector kit 3/8" adapter to the brass elbow (Item 24) on the valve.
PAGE 14
INSTALLING THE GAS LOG SET (Cont.) SPECIAL INSTRUCTIONS FOR G46-01-xx(M)(P) MODELS Installing pine cone with switch for 01M models CONNECTING THE IGNITION PACK TO THE G46-01(M)(P) VALVE The G46-01-xx(M)(P) valve comes complete with the wiring harness connected to the pine cone switch. You may wish to ensure it is correctly connected before finally connecting the three wires to the valve, as below. TO CHECK THE WIRING ASSEMBLY: CHECK CONNECTIONS Check Connections A.
PAGE 15
INSTALLING THE GAS LOG SET (Cont.) IMPORTANT For all valves, the air MUST be purged from the gas line before the pilot will light and burn properly. The time needed to purge will depend on the length of the gas line to the unit and the amount of time since the unit or gas line was last used. It may take several minutes before all the air is purged and the pilot will light and burn properly. Follow the relevant LIGHTING INSTRUCTIONS in this manual.
PAGE 16
WOODLAND OAK LOG PLACEMENT Note: For Charred series, see p. 16. For Western CampfyreTM series, see p. 17. Proper log placement is important to ensure proper performance of the Real-Fyre® gas log set. Be sure to follow the LOG PLACEMENT INSTRUCTIONS carefully. Three optional log placement patterns, an exclusive feature of the log set, are explained below. 24" Woodland Oak (WO) log set shown. 18"- 30" GAS LOG SETS 1 FOR ALL OPTIONS Step 1: Place the rear bottom log (Log #1) on the back of the grate (Fig.
PAGE 17
WOODLAND OAK LOG PLACEMENT (Cont.) Fig. 17-1 OPTIONAL BONUS LOG PLACEMENT The optional bonus log (included with Golden Oak Designer Plus and Split Oak Designer Plus log sets) should be placed directly above the front or rear bottom logs (Logs #1 & #2), so it does not extend into the space between the front and rear logs, as shown in Fig. 17-1. Log #7 OPTIONAL LOG PLACEMENT PATTERNS SUMMARY The illustrations below (Fig. 17-2 through 17-4 and Fig.
PAGE 18
EMBER BED SETUP If you have purchased this style of log set, follow the instructions below. Note: The logs for the CHD Charred Oak Set are illustrated. Log styles and sizes will vary depending upon the Charred Series log set ordered. Note: INSTRUCTIONS ON THE EMBER BED MAY NOT BE APPLICABLE. The ember bed (see Fig. 18-1), supplied with the charred log set, fits onto the back of the burner pan. Place it centrally on the back so the outer front tabs hang over the pan (see Fig. 18-2).
PAGE 19
WESTERN CAMPFYRETM LOG PLACEMENT WESTERN CAMPFYRETM STYLE LOGS LAYOUT SUMMARY If you have purchased this style of log set, follow the instructions below. 1 6 4 2 8 5 3 7 Fig. 19-1 1. MWCFL-18BR 2. MWCFL-18L 3. MWCFL-18R 4. MWCFL-13T 5. MWCFL-13TY Rear log Left log Right log Top log Top log ITEMS 6. MWCFL-10TY 7. MWCFL-8T1 8. MWCFL-11T 9. MWCFL-5T 9 Top log Top log Top log Top log Note: LOG PLACEMENT is very important for the proper operation and performance of the RealFyre® gas log set.
PAGE 20
INSTRUCTIONS D’ÉCLAIRAGE - SOUPAPE DE COMMANDE POUR VOTRE SÛRETÉ, LISEZ AVANT DE S’ALLUMER AVERTISSEMENT: Si vous ne suivez pas ces instructions exactement, une incendie ou une explosion peut résulter entraînant des dégats matériels, des blessures ou la perte de la vie. N’employez pas cet appareil si n’importe quelle partie a été sous-marine.
PAGE 21
LIGHTING INSTRUCTIONS - MANUAL PILOT VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.
PAGE 22
INSTRUCTIONS D’ÉCLAIRAGE - VALVE DE LA SÉRIE 11 POUR VOTRE SÛRETÉ, LISEZ AVANT DE S’ALLUMER AVERTISSEMENT : Si vous ne suivez pas ces instructions exactement, une incendie ou une explosion peut résulter entraînant des dégats matériels, des blessures ou la perte de la vie. N’employez pas cet appareil si n’importe quelle partie a été sous-marine.
PAGE 23
LIGHTING INSTRUCTIONS - SERIES 11 VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater.
PAGE 24
INSTRUCTIONS D’ÉCLAIRAGE - VALVE DE LA SÉRIE 01 * Nous recommandons qu’avant que vous installiez votre grosse bûche mise vous vous familiarisez avec la disposition de la valve du contrôle. Cela vous aidera pour être opérer plus confiant la grosse bûche mise quand a complètement installé. POUR VOTRE SECURITE, LISEZ AVANT D’ALLUMER PRÉVENIR: Si vous ne suivez pas ces instrucions exactement, un feu ou explosion peuvent résulter, en causant dégât de la propriété, blessure personnelle ou perte de vie.
PAGE 25
LIGHTING INSTRUCTIONS - 01 VALVE * We recommend that before you install your log set, you familiarize yourself with the control valve layout. This will help you to be confident operating the log set when fully installed. FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. The Real-Fyre® G46 Series gas log set has a pilot that can be lit by hand using the piezo ignitor.
PAGE 26
INSTRUCTIONS D’ÉCLAIRAGE - VALVE DE LA SÉRIE 15 POUR VOTRE SÛRETÉ, LISEZ AVANT DE S’ALLUMER AVERTISSEMENT : Si vous ne suivez pas ces instructions exactement, une incendie ou une explosion peut résulter entraînant des dégats matériels, des blessures ou la perte de la vie. N’employez pas cet appareil si n’importe quelle partie a été sous-marine.
PAGE 27
LIGHTING INSTRUCTIONS - SERIES 15 VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING If you do not follow these instructions exactly, a fire or explosion may result, causing property damage, personal injury, or loss of life. Do not use this appliance if any part has been underwater. Immediately call for a qualified professional service technician to inspect the appliance and to replace any part of the control system and any gas control that has been underwater. The Real-Fyre® burner system has a pilot.
PAGE 28
PILOT BURNER ADJUSTMENT (G46 MANUAL) The pilot burner is preset at the factory and normally should not require adjustment. However, if adjustment is necessary, the following steps should be taken: Fig. 28-1 Pilot adjustment Thermocouple With the pilot burner lit and the control knob in the pilot position, use a long, narrow screwdriver to turn the pilot adjustment screw (located on front of valve). Turn the adjustment screw slowly clockwise to reduce the flame, or counterclockwise to increase the flame.
PAGE 29
FLAME PATTERN ADJUSTMENT (ALL MODELS) To adjust the flame pattern, take a long-blade screwdriver or similar tool and stir the granules until the desired pattern is achieved. DO NOT REMOVE GRANULES FROM THE BURNER PAN. Long-bladed screwdriver (or similar) Insert blade into sand and stir granules in various places until desired flame pattern is achieved. MAINTENANCE Periodically remove the logs and examine the burner assembly. If dirty, clean with a stiff brush. Also examine the area around the pilot.
PAGE 30
AVAILABLE ACCESSORIES FOR THE GAS BURNER SYSTEM The following accessories are available for burner systems as indicated, and can be purchased separately from your local Peterson Real-Fyre® dealer. Before purchasing, make sure the accessory you desire is compatible with your specific model (for example, VR-2A is used with the series 15 systems). To install and operate any accessory, simply follow the instructions supplied with your accessory kit.
PAGE 31
AVAILABLE ACCESSORIES FOR THE GAS BURNER SYSTEM (Cont.) FOR SERIES 01, 10, 11, and 12: ON/OFF REMOTES AND RECEIVERS BATTERY-OPERATED REMOTE LIGHTING SYSTEMS FOR USE WITH NATURAL OR PROPANE GAS RR-2A RR-2A RR-1A RUS-1 Transmitter handset, Transmitter handset, receiver, wall switch, Transmitter receiver, handsethandset, holder, receiver,and wiring holder, wall switch, and wiring. wall handset switch, and wiring RUS-1 Transmitter handset, Transmitter handset, receiver.
PAGE 32
WARRANTY PETERSON VENTED GAS LOG SETS LIMITED WARRANTY All Peterson gas logs are WARRANTED for as long as you own them (lifetime). All Peterson burner assemblies are WARRANTED for TEN (10) YEARS. SPK-26 controls are covered by a THREE (3) YEAR “All Parts” Warranty. All other Peterson valves, pilots, and controls are covered by a ONE (1) YEAR Limited Warranty (excluding batteries).