Owner`s manual

ManualsBrandsR.H. Peterson ManualsLawn and GardenG8 series

REV 6 - 0903181423

NO. L-F2-06609

OWNER’S

MANUAL

Each set comprises of 2 separate boxes;

G8 series burner and VO8 log set

ROBERT H. PETERSON CO. • 14724 East Proctor Avenue, City of Industry, CA 91746

G8 SERIES VENT-FREE GAS LOG SET

G8-16(P)

G8-16-12(M)(P)

G8-20(P)

G8-20-12(M)(P)

G8-24(P)

G8-24-12(M)(P)

(20,000 BTU)

CERTIFIED

Unvented Room Heater Standard

ANSI Z21.11.2

and

Vented Decorative Appliance

ANSI Z21.60b

G8-16R(P)

G8-16R-12(M)(P)

G8-20R(P)

G8-20R-12(M)(P)

G8-24R(P)

G8-24R-12(M)(P)

(9,500 BTU)

Important: Read these instructions carefully

and completely before starting

installation of the log set.

This appliance is only for use with the type

of gas indicated on the rating plate.

This is an unvented gas-ﬁ red heater. It uses

air (oxygen) from the room in which it is

installed. Provisions for adequate combustion

and ventilation air must be provided. Refer to

section entitled VENTILATION AND CONFINED

SPACE INFORMATION.

This appliance is designed as an attended

appliance. Adults must be present when the unit

is operating. Do not leave this unit burning when

unattended or while anyone is sleeping.

Installation, service, and the provisions for combustion

and ventilation air MUST conform with local codes

and with the National Fuel Gas Code, ANSI Z223.1/

NFPA 54, or the CSA B149.1, Natural Gas And

Propane Installation Code.

This appliance may be installed in an

aftermarket, permanently located,

manufactured (mobile) home where not

prohibited by local codes.

This appliance is only for use with the type

of gas indicated on the rating plate. This

appliance is not convertible for use with other

gasses.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING

If the information in this manual is not

followed exactly, a ﬁ re or explosion may

result, causing property damage, personal

injury, or loss of life.

Do not store or use gasoline or other

ﬂ ammable vapors and liquids in the vicinity

of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS:

• Open a window.

• Do not try to light any appliance.

• Do not touch any electrical switch; do

not use any phone in the building.

• Immediately call the gas supplier from

a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach the gas supplier, call

the ﬁ re department.

Installation and service must be performed

by a qualified professional installer,

service agency, or the gas supplier.

Summary of content (28 pages)

PAGE 1
OWNER’S MANUAL G8-16(P) G8-16-12(M)(P) G8-20(P) G8-20-12(M)(P) G8-24(P) G8-24-12(M)(P) (20,000 BTU) G8-16R(P) G8-16R-12(M)(P) G8-20R(P) G8-20R-12(M)(P) G8-24R(P) G8-24R-12(M)(P) (9,500 BTU) CERTIFIED to Unvented Room Heater Standard ANSI Z21.11.2 and Vented Decorative Appliance ANSI Z21.
PAGE 2
TABLE OF CONTENTS TABLE OF CONTENTS GENERAL INFORMATION FIREPLACE SIZE REQUIREMENTS & BTU RATING INFORMATION MINIMUM CLEARANCE TO COMBUSTIBLES HOW TO CORRECTLY SIZE AND INSTALL MANTELS AND FIREPLACE HOODS MINIMUM CLEARANCE TO COMBUSTIBLES - ABOVE & IN FRONT OF FIREPLACE PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY IMPORTANT SAFETY INFORMATION INSTALLATION SAFETY INFORMATION INSTALLATION SAFETY GUIDELINES OPERATIONAL SAFETY INFORMATION VENTILATION AND CONFINED SPACE SAFETY INFORMATION LOGS - PARTS LIST
PAGE 3
GENERAL INFORMATION APPROVED INSTALLATIONS The G8 Series vent-free gas log sets are available with a manual ODS pilot, an on/off remote, or a variable flame height control valve that can be used with the remote transmitter and receiver. Subject to minimum fireplace size requirements specified below: A spark ignition system (piezo) allows the gas ODS pilot to be lit without the use of matches, and permits the operation of the appliance during a power outage. 1.
PAGE 4
FIREPLACE SIZE REQUIREMENTS & BTU RATING INFORMATION The minimum size of a fireplace for installation of Real-Fyre® G8 vent-free gas log set: (refer to Fig.
PAGE 5
MINIMUM CLEARANCE TO COMBUSTIBLES If the vent-free gas log set is installed in a factory built fireplace, follow the manufacturer’s guidelines for minimum clearances to combustibles. In the absence of such guidelines, follow the instructions below. Minimum to Minimumclearances clearances to sidewalls andceiling ceiling sidewalls and Clearances to Combustible Construction: 42" Sidewalls: 6" from side of fireplace opening (Fig. 5-1). Ceiling: 42" from top of fireplace opening (Fig. 5-1).
PAGE 6
MINIMUM CLEARANCE TO COMBUSTIBLES - ABOVE & IN FRONT OF FIREPLACE MANTEL CLEARANCES FOR G8 STANDARD BURNERS ONLY MANTEL WITHhood* HOOD* Mantel CLEARANCE clearance with MANTEL WITHOUThood HOOD MantelCLEARANCE clearance without 10" with a minimum 4 inch4" * Standard Fireplace *Standard fireplaceHood hood with a minimum horizontal projection. horizontal projection. HORIZONTAL Horizontal PROJECTION projection FROM FACE OF from face of FIREPLACE fireplace.
PAGE 7
PRE-INSTALLATION AND FIREPLACE PREPARATION SAFETY CAUTION: Installation and repair must be done by a qualified professional installer. Installer: Carefully read these instructions before installing this gas burner system. Be sure you understand all safety precautions and warnings contained in this manual. A. This appliance is only for use with the type of gas indicated on the rating plate. This appliance is NOT CONVERTIBLE for use with other gasses. B.
PAGE 8
IMPORTANT SAFETY INFORMATION ANSI Z21.11.2-2007 UNVENTED ROOM HEATER GENERAL SAFETY INFORMATION A. WARNING: CARBON MONOXIDE POISONING MAY LEAD TO DEATH. When used without fresh air, gas appliances may give off carbon monoxide, an odorless, colorless, poisonous gas. Early signs of carbon monoxide poisoning are similar to the flu, with headaches, dizziness, and/or nausea. If you have these signs, the gas appliance may not be installed correctly, or may not be working properly.
PAGE 9
INSTALLATION SAFETY INFORMATION INSTALLATION SAFETY GUIDELINES A. Carefully inspect the burner and log cartons for shipping damage. If any parts are missing/ damaged, call your dealer. Do not attempt to install the appliance unless all parts are in good condition. B. Correct installation of the glass or the ceramic refractory log set and proper placement and installation of burner assembly, including ember placement and Lava Granule placement, are crucial to safe operation of your set.
PAGE 10
OPERATIONAL SAFETY INFORMATION OPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLY A. SOLID FUEL MUST NOT BE BURNED in a fireplace where this vent-free gas appliance is installed. B. GLASS DOORS MUST BE FULLY OPEN when this vent-free gas appliance is operating. This appliance MUST NOT BE ON if glass doors are closed, as it can lead to sooting, burner outages, and possibly explosion, causing damage or injury. C. WARNING: DO NOT ALLOW DRAFTS INTO OR AROUND THE FIREPLACE.
PAGE 11
OPERATIONAL SAFETY INFORMATION (Cont.) OPERATING YOUR UNVENTED GAS APPLIANCE SAFELY AND CORRECTLY M. This appliance is intended for supplemental heating, and is not to be used as a primary heating source. Water vapor produced by vent-free gas logs can create moisture problems in a home when operated for extended periods of time. If condensation begins to occur, open your damper or a window.
PAGE 12
VENTILATION AND CONFINED SPACE SAFETY INFORMATION IT MAY BE NECESSARY TO OPEN A WINDOW SLIGHTLY (1"- 2") OR OTHERWISE INCREASE VENTILATION. Conditions requiring this include, but are not limited to: 1. 2. 3. 4. Installation in a confined space. Installation in a tightly constructed home. Installation at high altitudes. Certain medical or physical conditions of the homeowner that may be adversely impacted by combustion products created by burning natural or propane gas.
PAGE 13
LOGS - PARTS LIST WARNING Failure to position the parts in accordance with these diagrams, or failure to use only parts specifically approved with this heater, may result in property damage or personal injury. 5 6 3 4 2 Contact your local Real-Fyre® dealer for parts and accessories. 1 VO = Valley Oak ITEM NO. 1. PART NO. DESCRIPTION VOL8-24BF Valley Oak bottom front log (for 24" log set) 2. VOL8-12BR Valley Oak bottom rear log 3. VOL8-10TL Valley Oak left log 10" 4.
PAGE 14
BURNER PARTS LIST FOR MANUAL VALVE Contact your local Real-Fyre® dealer for parts and accessories. ITEM NO. DESCRIPTION ITEM NO. DESCRIPTION 1. 2. 3. 4. 5. 6. 7. Valve control knob Ignitor Face plate with security holes ODS mounting bracket Manual valve ODS pilot (natural or propane) Burner mounting bracket 8. Connector kit, poly coated 3/8"x 24" 9. 10. Regulator (natural or propane) Reducing elbow 11. 3/ 1 8" x /4" Bushing 12. 13. 14. 15. 16. 17. 18. 1/ 19.
PAGE 15
WHEN USED AS A VENTED DECORATIVE APPLIANCE (PER ANSI.60b-2004) This appliance is for installation in a solid fuel burning fireplace (masonry fireplace or manufactured fireplace) with a working flue and constructed of noncombustible material. These gas logs may be installed as vented decorative log sets in compliance with ANSI Z21.60b-2004 and National Fuel Gas Code, Section 6.6. The minimum permanent free opening of the fireplace chimney or chimney damper must be at least 14.1 sq. in.
PAGE 16
CONNECTING THE GAS TO THE BURNER SYSTEM (Cont.) 1. Center the burner assembly in the fireplace. Make certain that no part of the assembly protrudes beyond the face of the fireplace. 2. Attach the large adaptor fitting of the flex connector kit (Item 8, Item 28) to the gas supply line using a pipe compound resistant to propane gas or Teflon tape. Tighten the connection. Connect one end of flex connector to the large adaptor, and the other end to the flare connector fitting on the burner assembly (see Fig.
PAGE 17
CHECKING GAS PRESSURE WARNING Do not connect this appliance directly to a high pressure natural gas line or an unregulated propane tank. Test all gas joints for leaks using a half-and-half soapy water solution after completing connection. DO NOT USE AN OPEN FLAME WHEN CHECKING FOR GAS LEAKS. Important: Check the gas pressure with the vent-free gas log set burning and the control set to HIGH.
PAGE 18
LOG PLACEMENT WARNING: Failure to position the parts in accordance with these instructions, or failure to use only parts specifically approved with this heater, may result in property damage or personal injury. Carefully follow the detailed instructions for correct log placement Note: Each log in the Real-Fyre® vent-free gas log set has a number engraved in the back to aid in the log placement procedures. Rear log locks into place on ODS pilot bracket 1.
PAGE 19
CLEANING AND SERVICING Note: Regular cleaning and servicing will be necessary to ensure proper ODS pilot operation and proper burn characteristics. A. Always shut off the gas to the vent-free gas log set while performing service work. B. Allow the vent-free gas log set to cool before servicing. C. Installation and repair must be done by an NFI Certified or other qualified professional installer. The gas log set should be inspected regularly to prevent burner shutdown, sooting, odors, etc.
PAGE 20
CLEANING AND SERVICING (Cont.) Only limited cleaning will be required under normal use of the vent-free gas log set. TO CLEAN THE LOG SET 1. Remove the logs. Use a vacuum cleaner to remove loose particles from all surfaces of the logs. Do not use cleaning fluids to clean the log or any other part of the log set. 2. Dust the grate, the base of the assembly and the burner. 3. Replace the logs as instructed in the LOG PLACEMENT section of this manual.
PAGE 21
CLEANING AND SERVICING (Cont.) 4. If the ODS pilot flame does not burn as indicated in the instructions, extinguish the ODS pilot by turning the valve to the full OFF position. Using a compressed air duster (commonly available at computer, electronic or office supply stores), insert the flexible nozzle through either air intake openings, insuring that the nozzle is pointed toward the ODS pilot opening (see Fig. 21-1).
PAGE 22
OPERATING THE LOG SET - LIGHTING AND EXTINGUISHING FOR YOUR SAFETY, READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. • If you cannot reach the gas supplier, call the fire The Peterson Real-Fyre® gas log set has an ODS pilot department. which must be lit by hand. When lighting the ODS pilot, follow these instructions exactly. C. Use only your hand to push in or turn the gas control knob.
PAGE 23
LIGHTING INSTRUCTIONS FOR REMOTE READY 12 SERIES VALVE FOR YOUR SAFETY, READ BEFORE LIGHTING If you do not follow these instructions exactly, a fire or explosion may result causing property damage, personal injury or loss of life. Fig. 23-1 2. Turn OFF any electrical appliance (such as the Peterson Warm Air Circulator) if used with the log set. Control knob in OFF position Read setting here 3.
PAGE 24
OPERATING THE REAL-FYRE® GAS LOG SET Observe the flames. The flames should be blue at the base and a combination of blue/yellow at the body and tips. Flames should be 2" to 4" tall (see Fig. 24-1). Every Real-Fyre® vent-free gas log set leaves the factory tested and quality checked to ensure that it has been manufactured to the strict specifications to which it was submitted and approved for certification by the American Gas Association.
PAGE 25
TROUBLESHOOTING POSSIBLE CAUSE 1 SOLUTIONS BURNER SHUTTING DOWN DURING OPERATION A. Insufficient or excessive gas pressure A1. Check gas pressure (check with local gas company). For natural gas, pressure must be minimum 5" w.c. at fireplace with burner operating. Maximum inlet gas pressure is 10.5", w.c. Reading at inlet pressure tap (farthest to valve inlet) on remote-capable valves burners should be 5" w.c. (minimum). With the knob on high, maximum inlet pressure is 10.5" w.c. A2.
PAGE 26
TROUBLESHOOTING (Cont.) POSSIBLE CAUSE 2 SOLUTIONS ODS PILOT WILL NOT LIGHT A. ODS pilot flame lifting off thermocouple/generator A. Check gas pressure. B. Piezo spark not lighting ODS pilot B. Check to make sure piezo is sparking when turning ignitor control knob. (Note: You may need to turn ignitor several times to ignite ODS pilot.) See LIGHTING INSTRUCTIONS section. C. Gas supply off/manual shutoff valve closed C. Turn on gas supply or open manual shutoff valve. D. Air in gas line D.
PAGE 27
TROUBLESHOOTING (Cont.) POSSIBLE CAUSE 9 SOLUTIONS SOOTING A. Low gas pressure A. Check gas pressure. B. Drafts in room B. Eliminate drafts by closing heating and air conditioning vents, returns, and outside air vents. Fans blowing directly into fireplace should be turned off when set is operating. C. Air shutters blocked C. Burner air shutters are blocked with debris. Vacuum debris in and around burner area. D. Log placement D.
PAGE 28
WARRANTY PETERSON VENT-FREE GAS LOG SETS LIMITED WARRANTY All Peterson vent-free ceramic refractory gas logs are WARRANTED for as long as you own them (lifetime). All Peterson vent-free fiber ceramic gas logs are WARRANTED for SEVEN (7) YEARS. All Peterson vent-free burner component parts, except valves, ODS pilots, and controls, are WARRANTED for TEN (10) YEARS. All Peterson valves, ODS pilots, and controls are covered by a ONE (1) YEAR Limited Warranty (excluding batteries).