Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 EurglE 2.4ghz 3 ChannEl lCD WhEEl Digital programmablE raDio gEar (baCklight SCrEEn) Instruction Manual You should read this Manual carefully before you play. It contains important information for using the model. Join our FREE Membership and accept 10%off Offer! R2hobbies.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Content INTRODUCTION REMARKS ITEM LIST SAFTY GUIDES 2.4Ghz SYSTEM BATTERY CHARGING NOTES - TRANSMITTER CHARGER - RECEIVER CHARGER TANSMITTER PARAMETERS RECEIVER PARAMETERS RECEIVER CONNECTIVITY - INSTALLATION WHEN A MOTOR CONTROLLER IS IN USED - INSTALLATION FOR GAS POWERED MODELS 2.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Introduction Thank you for choosing EURGLE 2.4G 3 Channel LCD Wheel Digital Programmable Radio Gear, if you are the first time to use this type of Products, please read this statement carefully and strictly in accordance with the requirements of operation. You could refer to the manual if you encounter any problems during the operation. Please well keep the manual after use because you might have to use it again next time.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 The system works in between 2.400GHz to 2.4835GHz frequencies that have been divided into 160 frequency points. Each system uses 16 frequencies points and 160 hopping frequency. By using various switching-on time, frequency hopping and different frequency points, the system can passively avoid frequency jamming.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Transmitter Parameter Channels : 3 Channels Model Type : Car/ Boat RF Power : No more than 10mW Modulation : GFSK System Type : AFHDS Sensitivity : 1024 Low Voltage Warning : Yes (Less than 9.5V) DSC Port : Yes (3.5mm) Charger Port : Yes Power : 12VDC (1.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Receiver Connectivity Installation when a motor controller is used. Remark : Place the antenna of the receiver vertically with the plane! And don’t let it close to the metal thing for assuring its sensitivity.(See Figure 1) Installation for Gas Powered Models Join our FREE Membership and accept 10%off Offer! R2hobbies.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 2.4Ghz Operation Notes Matching (Code) Our products are well matched in the factory; you do not need to match by yourself. But if your are going to match the receiver with other transmitter or you needs to change a new receiver or transmitter, please follow the following steps: 1. Install the battery to 2.4G transmitters and shut it down. 2. Insert the matching lines to the channel BIND / CH3 port of the receiver. 3.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Each Part of E3T Transmitter 1. 2.4Ghz Antenna 2. Steering Wheel 3. Channel 3 4. Battery Box 5. D/R 6. Channel 3 Trim 7. Power 8. DSC for Simulate 9. Charger A. Throttle Trigger B. LCD C. Back D. Bind E. End F. Enter (Right / Left) G. TH Trim (Down) H. TH Trim (Up) I. ST Trim (Left) J. ST Trim (Right) Join our FREE Membership and accept 10%off Offer! R2hobbies.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 LCD Function Explanation LCD Display 1. Turn the ENTER button counterclockwise: decrease the rate 2. Turn the ENTER button: increase the rate 3. Press ENTER button: select the menu 4. Press BACK button: return to the menu 5. Press END button: end the programming OPENING SCREEN 1. Show current model number and user name, Press ENTER button, the screen will show voltage and model number 2.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 NAME 1. Function explanation - This function allows you to assign a number to each model memory and a user name ( three characters). 2. Parameter specification - MODEL NO: Model number - ACB: User name 3. Operation - Press the “ENTER” button and turn to select the NAME option. The selected function will be blinking. Select the channel by turning the “ENTER” button, and then press the “END” button.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 REV 1. Function explanation - This function reverses the direction of the operations of servos: steering, throttle, and channel 3. 2. Parameter specification - Channel : 1 to 3 - REV : Reverse - NOR : Normal 3. Operation - Press the “ENTER” button and turn to select the TRIM option. The selected function will be blinking.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 E. POINT 1. Function explanation - Use this function when performing left and right steering angle adjustments, throttle high Side/brake side amount adjustment, and channel 3 servos up side/down side operation amount adjustment during linkage setup. - It use correct steering angel of adjusting left and right steering angles when there is a difference in the Left and Right turning radios. 2.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 TRIM 1. Function explanation - Use this function to adjust the neutral position of the steering, throttle and channel 3 servos. 2.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 D/R 1. Function explanation - By setting the dual rates function, you can limit the total travel of each individual Channel. 2. Parameter specification - CHANNEL : 1 to 3 - Dual Rate : 100%, When you want to increase the servo travel, turn the button to increase the rate. When you want to decrease the servo travel, turn the button to decrease the rate. 0% is no signal output, 100% is maximum signal output.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 EXP : 1. Function explanation - This function is used to change the sensitivity of steering servo’s 3 channels around the neutral position. In order to “Soften” the response according to user’s demand. 2. Parameter specification - CHANNEL : 1 to 3 - Steering EXP rate 100% When you want aggressive steering operation, turn the button to increase the rate.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 ABS 1. Function explanation - While applying the brakes, locking them up can be easily done, which can cause your vehicle to spin out of control, this can be eliminated by pulsing the brakes, so that full control of your vehicle can be achieve at all times. The effect as like that of a A.B.S in a real passenger car. 2. Parameter specification - CHANNEL: It’s only available in channel 2. - OFF : A.B.S.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Transmitter Function Notes STEERING CONTROL 1. Function explanation - This function is to control the direction, When the steering turn to right then the front wheel will turn to right ( see the picture), When the steering turn to left then the front wheel will turn to left. 2. Operation - Adjust the dual rate of the steering by adjusting the D/R knob. THROTTLE CONTROL 1.
Eurgle 2.4Ghz 3 Ch LCD Wheel Digital Programmable Radio Gear rcps2805004 Fail Safe Function Function Failsafe aims to prevent out-of-control driving of RC Car or RC Boat. If the Receiver is not able to receive any signal, from the control to Throttle, the parameter of Throttle on Receiver will turn back to its original setting. Setting 1. Turn on the Transmitter switch 2. Turn on the Receiver switch, the LED will be lighting 3.