Specifications

ManualsBrandsR2hobbies.com ManualsRemote ControlEurgle

80A Brushless Speed Controller

INSTRUCTIONS

Warnings

· We strongly recommend to calibrate the throttle range of transmitter when you first use the controller or

when using a new/different transmitter or receiver.

·When connecting the ESC to battery pack, please ensure the polarity is correct. Incorrect polarity may cause

permanent damage to the ESC and such damage is not covered by manufacturer’s WARRANTY.

·When you use the ESC, turn on the transmitter BEFORE powering on the receiver.

·When you finish the flying, power off the receiver BEFORE turning off the transmitter.

·The limiting current is set to the ‘standard mode’ in factory. It is suitable for use in most configurations.

Only experienced technicians can adjust this programming.

·In Governor Mode, the brake is always disabled and the soft cutoff is always active.

·Changing the PWM may cause the motor to heat ahead of time.

·Never disconnect the battery pack while the motor is running, as this could cause damage to the speed con-

troller and/or motor.

·Connectors with low conductivity may cause erratic motor rotations or other unexpected

movements.

·If you do not use the BEC function of the ESC and are using a separate receiver pack or UBEC to power

receiver and servos instead, please disconnect the red wire from the ESC’s receiver lead.

·Due to adopt advanced switching BEC technology, the switching frequency of the on-board BEC may make

some disturbance to receiver when use with some of 35Mhz transmitters and receivers, (such as Multiplex

35Mhz transmitter and receiver). We strongly recommend to disconnect the red wire from the ESC’s receiver

lead and use a separate receiver battery to power the receiver and servos when use with some of 35Mhz trans-

mitter and receiver.

·The controller will automatically power off the motor if the battery voltage drops below the programmed

cut-off voltage (factory preset at 6.0V). Try using a smaller prop on the motor, or using batteries with a higher

rating. It is especially important for the user of Li-poly cells.

·Allowing water, lubricants, moisture or other foreign objects inside the ESC will VOID the WARRANTY.

Exposure to CA glue or its fumes can cause damage and malfunctions; this will also VOID the WARRANTY.

Summary of content (14 pages)

PAGE 1
80A Brushless Speed Controller INSTRUCTIONS Warnings · We strongly recommend to calibrate the throttle range of transmitter when you first use the controller or when using a new/different transmitter or receiver. ·When connecting the ESC to battery pack, please ensure the polarity is correct. Incorrect polarity may cause permanent damage to the ESC and such damage is not covered by manufacturer’s WARRANTY. ·When you use the ESC, turn on the transmitter BEFORE powering on the receiver.
PAGE 2
Eurgle ESC-80A MANUALS 2 page/ 14pages ⅠIntroduction The Eurgle controllers are outstanding and unique products in the R/C industry. They represent a great advance in electric flight by integrating a data logger with an electronic speed controller. There is no need for a separate logging device if you have a Eurgle controller! In addition, software updates for the controller can be downloaded from the Internet so your controller will never become obsolete.
PAGE 3
Eurgle ESC-80A MANUAL 3page/14pages Ⅵ Using the ESC ·Calibrate the throttle range of transmitter at the first time to use the controller (Recommend) - Correctly connect the ESC with brushless motor, plug the receiver lead of ESC into receiver ( usually into Channel 3); - Put the throttle to the highest position, turn on the transmitter; - Power on the receiver, ESC and motor. There are 3 beeps emitted from the motor, which indicates all electronics are correctly power on for the setting.
PAGE 4
Eurgle ESC-80A MANUALS 4 page/14pages ·In order to well record the flight data and utilize the storage of the logger, please set the ‘Recorder Configuration’ in the menu of ‘Data Logger’ after installing the Eurgle software. (see instructions in Ⅸ) ·When you finish the setting, repower the ESC, receiver and motor, there are two beeps emitted from the motor, then is ready to go fly and enjoy the flying. Ⅶ Installing Eurgle Software ·Insert the CD in the CD driver of the computer.
PAGE 5
Eurgle ESC-80A MANUALS 5page/pages ·After you click the ‘finish’ button, there will be an icon ‘Eurgle’ on your computer desktop. ·Installation complete. NOTE: These two destination folders are both default and cannot be changed, otherwise the software cannot work normally. Ⅷ How to connect the controller to PC ·Plug the receiver lead of ESC-80A into the Eurgle USB Linker, please pay attention to the polarity for correct connection. (Seeing the label on the USB Linker) .
PAGE 6
Eurgle ESC-80A MANUALS 6page/14pages Ⅸ Using the software ·Open the software by double clicking the icon ‘Eurgle’ on your desktop. ·Select the com port by clicking the menu of ‘Port Num.’* *The com port is generally ‘com 3’ or ‘com 4,’ but there are respective com ports on different computers. You can find the accurate com port on your computer in this way: Click the right button of mouse the icon ‘My Computer’→Manage → Device Manager →Ports(Com & LPT).
PAGE 7
Eurgle ESC-80A MANUALS 7page/14pages · Programming the parameters of the ESC: - Select ‘Programming Set’. (also the Shortcuts button ) - Click ‘Connect’ button or ‘Reading Data from ESC’ button to read out the current parameters of controller, and the firmware version is also displayed below. - Select the parameters you wish to set. - Click the ‘Update’ button to save the modification. - Clicking the ‘Back to default’ button will modify the parameters of ESC to factory default.
PAGE 8
Eurgle ESC-80A MANUALS 8page/14pages · Reading the flight data from the ESC-80A - Make sure to input the correct parameters in the area of ‘User Parameter’: Gear Rate and Magnet Poles number of motor (the default value is: 1 and 2), it is very important to get the correct motor RPM information. - Click the ‘upload record data’ button to upload the flight data from the controller. - After clicking the ‘upload record data’ button, the flight data in ESC will be shown as curves in the display window.
PAGE 9
Eurgle ESC-80A MANUALS 9page/14pages - In the display window, you can choose a range of curves to analyze clearly by clicking the left button of mouse from start side to the end side of your chosen area, such as the below diagrammatic curves, data recorded from the 22.9 second to the 36.7 second as the chosen analyzing area (the area shown in translucent): - Much clearer curves of the chosen area is displayed: - Click the right button of mouse to display the original curves.
PAGE 10
Eurgle ESC-80A MANUALS 10page/14pages · Changing the recording parameters Recommend: In order to well and accurately record the flight data, please know and program the recording configurations first before use, otherwise may cause losing of some data. - Click the menu ‘Data Logger’. - ‘Recorder Configuration’ (Shortcuts button ). - Click ‘Connect’ button to display current configuration. - Sampling Rate (1,2,3,5,10,20,30 ) times/a second.* *The default sampling rate of ESC-80A is 3 times in a second.
PAGE 11
Eurgle ESC-80A MANUALS 11page/14pages - ‘Cur fly times’ button is never highlighted.* *‘Cur fly times’ button records the times you have flown. The ESC can record most 16 times flying. You can clear it by clicking the ‘Clear Logger Data’ button. That battery in power is calculated as once. - Select the configuration you wish to set, and click ‘Update’ to save modifications. - Click the button ‘Clear Logger Data’ to clear the data in the ESC for enough space to record for the next flying.
PAGE 12
Appendix Eurgle ESC s offer eight user programmable features, including low cutoff voltage, current limiting, brake type, timing advance, cutoff type, soft start, governor mode and PWM switching rate. Through the USB Linker, Eurgle ESC-80A can be programmed easily on PC, and it is also good compatible with Eurgle Program Card or program via throttle stick of the transmitter. · Low Cut-off Voltage Option 1:Auto Lipo Auto Lipo Cells Detecting Option2:6.
PAGE 13
· Timing Advance Option 1: Low advance timing 0°~15° Option 2: middle advance timing Recommended for most motors .Gives a good balance of power and efficiency. 5 °~ 20 ° Option 3: High advance timing Recommended for most of higher pole count motors 15° ~ 30 ° Option4:Auto(default) Recommended for most of all brushless motors. · Cutoff Type When battery voltage reaches cut-off voltage the motor will shutdown immediOption 1 :Hard cutoff (default) ately.
PAGE 14
· PWM Switching Rate Option 1:8KHz(default) Recommended for most brushless motors Option 2: 12KHz Recommended for low inductance motors Option 3: 16KHz Recommended for very low inductance motors Note: we strongly recommend only the experienced modeler could change this setting. Ⅹ All models of Eurgle controllers Dimension (mm) Weight (with cables) 2amp (Linear) 55×27×12 23g 40/50amp 2amp (Linear) 55×27×12 25g 2-6S Lipo 60/70amp 4amp (Switching) 71×26.