Cut Sheet

ManualsBrandsRAB ManualsLightingHigh Bay Occupancy Sensor

LOSBAY800

BAY SENSOR

Installation Manual

LOSBAY800 Specications

Coverage Area: 50’- 60’ diameter @ 40’ height

Time Delay: 30 seconds to 30 minutes

Photocell Adjustment: 3.7 fc to185 fc (40 - 2000 Lux)

Operating Temperature: -10°C to 70°C (14°F to 160°F)

Relative Humidity: 20-85%

Power Consumption: 2W@120V, 1W@277V, 0.8W @347V

Switching Capacity:

120VAC: 800VA - 6.67A, 50/60 Hz

277VAC: 1200VA - 4.33A, 50/60 Hz

347VAC: 1500VA - 4.32A, 50/60 Hz

Summary of content (8 pages)

PAGE 1
LOSBAY800 BAY SENSOR Installation Manual LOSBAY800 Specifications Coverage Area: Time Delay: Photocell Adjustment: Operating Temperature: Relative Humidity: Power Consumption: Switching Capacity: 120VAC: 277VAC: 347VAC: 50’- 60’ diameter @ 40’ height 30 seconds to 30 minutes 3.7 fc to185 fc (40 - 2000 Lux) -10°C to 70°C (14°F to 160°F) 20-85% 2W@120V, 1W@277V, 0.8W @347V 800VA - 6.67A, 50/60 Hz 1200VA - 4.33A, 50/60 Hz 1500VA - 4.
PAGE 2
CAUTION: For your own safety and to prevent damage to the unit, turn off ALL power by removing the power fuse or turning off the circuit breaker. • Please read the entire Installation Manual before proceeding. • All wiring should comply with local electrical codes and requires a qualified electrician. • Use this device with copper or copper clad wire only. With aluminium wire use devices marked CO/ALR or CU/AL only. • • • • • Warmup: After the power is turned ON, allow 2 minutes for warm up.
PAGE 3
1. The sensor is supplied with two lenses, a factory installed 360° Bay Lens and an optional un-installed Aisle Lens (black color trim ring) . If people can not see the sensor lens from their normal positions in the area, the sensor will not detect their presence. 2. To change lens, turn the trim ring so that the two indented dots line up and pull out by the finger tabs. Dots LUX Locate the LOSBAY800 where it has an unobstructed view of the area, particularly the areas normally occupied by people.
PAGE 4
Mounting BAYLED Mounting R-Bay Mounting 1. The LOSBAY800 sensor threads into a 1/2” NPS hole on the end of a housing or junction box. To mount to BAYLED use stem as shown. LOSBAYMK can be ordered separately if needed. 1. The included adaptor may be used as shown, to expand the sensor’s field of view if it is obstructed by the RBAY. As long as sensor is mounted within 1” from the bottom of the fixture, the field of view will not be affected. 2.
PAGE 5
Limited Warranty Maintenance & Repair Your LOSBAY800 will be replaced or repaired at our option if it proves to be defective in workmanship or materials within five year from the date of original purchase. LOSBAY800 requires no maintenance other than keeping the lens area clean and free of obstructions. Clean outer surface with a damp cloth only. Do not attempt to open or repair the sensor. There are dangerous voltages inside the case, and no user serviceable parts. Opening the sensor voids the warranty.
PAGE 6
® ® GDBAYLEDW WIRE GUARD GDBAYLEDW WIRE GUARD Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.
PAGE 7
® ® GDBAYLEDP POLY SHIELD GDBAYLEDP POLY SHIELD Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.
PAGE 8
® ® GDBAYLED78FP FROSTED POLY SHIELD GDBAYLED78FP FROSTED POLY SHIELD Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000, or email: marketing@rabweb.com Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.