STEALTH STL200/277 Installation Manual STL200/277 Specifications: Switching Capacity: 8 amps Voltage: 277 volts 1000 watts incandescent Detection Pattern: 50’ x 200° Time Adjustment: 5 seconds to 12 minutes Power Consumption: 1 watt Surge Protection: I.E.C.
CAUTIONS: TURN OFF ALL POWER AT CIRCUIT BREAKER/FUSE PANEL. • Read entire Installation Manual before proceeding. • All wiring should comply with local electrical codes and requires a qualified electrician • The total lighting load connected to a STEALTH must not exceed 8 amps (1000 watts incandescent). To switch more wattage an electrician can install a relay. • Line Carrier Remote Control Systems such as X-10, Levitron or Radio Shack are incompatible with sensors and cause false activations.
How does the STEALTH work? STEALTH’s infrared sensor “sees” small temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically. It welcomes visitors and may deter intruders. How long do the lights stay on? Lights remain on as long as there is movement within the protection zone. Once the zone is vacated, lights can be adjusted to remain on from approximately 5 seconds-12 minutes.
Choosing a Location • Choose a location so that the sensor can “see” all paths of movement. • The sensor may be wall or ceiling mounted. • As distance from the sensor increases, it takes more movement to be detected. For example: a half-step will register at ten feet, but not at 40 feet. 40 feet will need several steps for detection. How does the LED Detection Indicator work? The red LED above the lens shows the logic state of the sensor.
Kit Wiring 1. Attach the Universal Mounting bar to the junction box with the bar screws (provided). To attach the STL200 kit to a surface mount weatherproof box, you must use the metal plate with the attached gasket. The gasket faces the junction box. Hook Universal Mounting Bar CU4 EZ Plate Insert close-up plugs in unused holes 3. Bring power leads and sensor kit leads through holes in all gaskets and into junction box. 4. Strip ½” of insulation from all leads. 5.
Wiring Diagrams Basic Wiring Diagram White Multiple Fixtures Ground Power In Red Black Sensor Basic Kit Wiring Diagram Note: Pigtail is only used to switch remote or additional light fixtures. Red (pigtail) Red Black Switchplate Label Black Power In White Ground • Multiple fixtures may be wired to a single sensor • To handle loads greater than 1,000 watts, a qualified electrician should install a relay. Switchplate label has self-adhesive backing.
Aiming and Walk Testing Walk Test: The purpose of the Walk Test is to check and adjust the coverage pattern. STEALTH has a 5 minute Test Period which allows the sensor to be aimed and walk-tested day or night. If you require 5 more minutes of Test Time, turn the power off for at least 10 seconds and back on again. During the Test Period, the sensor will keep lights on for 5 seconds each time it detects movement in its Detection Zone. The sensor will change to Automatic Mode after 5 minutes of testing. 3.
Technical Tips: Lights Do Not Turn Off 1. Make sure the sensor is not in Manual Override Mode. Turn power OFF for 10 seconds and then ON again. Sensor will be in Test Mode for approximately 5 minutes, then it will switch to Auto Mode with lights off, ready to detect movement. 3. Make sure sensor and lights are mounted firmly and do not move, even slightly, when touched. If they move, tighten all screws. 2.
Technical Tips: Lights Turn On and Off Incorrectly 1. Make sure the sensor is installed on its own dedicated circuit, free of motor loads such as HVAC equiptment, kitchen appliances, or garage door openers. 2. It is not recommended to wire sensors in parallel. More than one sensor wired together makes them difficult to troubleshoot. Disconnect multiple sensors and test separately. 3. Keep all people completely out of the detection pattern to make sure the sensor is not detecting them. 4.
Technical Tips: Lights Do Not Turn On 1. Check that lamps and fixtures work. Compare wiring to the Wiring Diagram in this manual. Check that the power is on. 2. If installing during daylight, remember that after power is turned on, the sensor will provide 5 minutes of Test Time. After 5 minutes, the sensor will switch to Automatic Mode and will not work during daylight if the photocell control is turned to night-only (moon) position.
Technical Tips: Range Appears Limited 1. Check that the sensor is level from side to side and pointed at desired area. If unit is tilted, part of the Detection Zone may be high in the air over people’s heads. 3. Check that movement is not directly towards sensor. Sensor will see movement across its pattern more quickly. To fix, move sensor. Less Sensitive WRONG! Solution: Position sensor exactly level from side to side. More Sensitive 4.
Technical Tips: Lights Turn On for Unknown Reasons 1. Lights may turn on occasionally during rain, snow and windstorms because the sensor detects changes in temperature. Solution: mount sensor in protected area. 3. You may not be aware of animals triggering the sensor. Create an “Animal Alley” by aiming sensor or masking the lower portion of the lens with opaque weatherproof tape to reduce triggering. 10’ “Animal Alley” 50’ 4.
Limited Warranty Your STEALTH will be replaced or repaired, at our option, if it proves to be defective in worksmanship or materials within ten years from the date of original purchase. For repair or replacement, return the product, freight prepaid and insured, to: RAB Lighting 170 Ludlow Avenue Northvale, NJ 07647 The STEALTH should be packed carefully. Please include your sales receipt and a description of the problem.
Contents: STL200/277 • Crossbar with Green Ground Screw • Hanging Hook • 1/2” Close Up Plugs (3) • Slotted Screws (4) • Indoor Switchplate Label • Wire Nuts (3) • Lens Mask (2) • • • • • Finishing Cap O-ring Gasket Center Mounting Screws CU4 Plate Metal Plate CU4 13 Metal
Easy Installation & Product Help ©2016 RAB LIGHTING Inc. Northvale, New Jersey 07647 USA STL200/277V IN 1016 Tech Help Line Call our experts 888 RAB-1000 rabweb.com Visit our website for product info email Answered promptly sales@rabweb.
STEALTH STL200-LED Installation Manual STL200-LED Specifications: Switching Capacity: 8 amps Voltage: 120 volts 300W on LED fixture Detection Pattern: 50’ x 2000 Time Adjustment: 5 seconds to 12 minutes Power Consumption: 1 watt Surge Protection: I.E.C.
CAUTIONS: TURN OFF ALL POWER AT CIRCUIT BREAKER/FUSE PANEL. • Read entire Installation Manual before proceeding. • All wiring should comply with local electrical codes and requires a qualified electrician • The total lighting load connected to a STEALTH must not exceed 8 amps (300W on LED fixture). To switch more wattage an electrician can install a relay. • Line Carrier Remote Control Systems such as X-10, Levitron or Radio Shack are incompatible with sensors and cause false activations.
How does the STEALTH work? STEALTH’s infrared sensor “sees” small temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically. It welcomes visitors and may deter intruders. How long do the lights stay on? Lights remain on as long as there is movement within the protection zone. Once the zone is vacated, lights can be adjusted to remain on from approximately 5 seconds-12 minutes.
Choosing a Location • Choose a location so that the sensor can “see” all paths of movement. • The sensor may be wall or ceiling mounted. • As distance from the sensor increases, it takes more movement to be detected. For example: a half-step will register at ten feet, but not at 40 feet. 40 feet will need several steps for detection. How does the LED Detection Indicator work? The red LED above the lens shows the logic state of the sensor.
Wiring Diagrams Multiple Fixtures Basic Wiring Diagram White Ground Power In Red Black Sensor Basic Kit Wiring Diagram Note: Pigtail is only used to switch remote or additional light fixtures. Red (pigtail) Red Black Switchplate Label Black Power In White Ground • Multiple fixtures may be wired to a single sensor • To handle loads greater than 300 watts, a qualified electrician should install a relay. Switchplate label has self-adhesive backing.
Aiming and Walk Testing Walk Test: The purpose of the Walk Test is to check and adjust the coverage pattern. STEALTH has a 5 minute Test Period which allows the sensor to be aimed and walk-tested day or night. If you require 5 more minutes of Test Time, turn the power off for at least 10 seconds and back on again. During the Test Period, the sensor will keep lights on for 5 seconds each time it detects movement in its Detection Zone. The sensor will change to Automatic Mode after 5 minutes of testing. 3.
Technical Tips: Lights Turn On for Unknown Reasons 1. Lights may turn on occasionally during rain, snow and windstorms because the sensor detects changes in temperature. Solution: mount sensor in protected area. 3. You may not be aware of animals triggering the sensor. Create an “Animal Alley” by aiming sensor or masking the lower portion of the lens with opaque weatherproof tape to reduce triggering. 10’ “Animal Alley” 50’ 4.
Technical Tips: Lights Do Not Turn Off 1. Make sure the sensor is not in Manual Override Mode. Turn power OFF for 10 seconds and then ON again. Sensor will be in Test Mode for approximately 5 minutes, then it will switch to Auto Mode with lights off, ready to detect movement. 3. Make sure sensor and lights are mounted firmly and do not move, even slightly, when touched. If they move, tighten all screws. 2.
Technical Tips: Lights Turn On and Off Incorrectly 1. Make sure the sensor is installed on its own dedicated circuit, free of motor loads such as HVAC equiptment, kitchen appliances, or garage door openers. 2. It is not recommended to wire sensors in parallel. More than one sensor wired together makes them difficult to troubleshoot. Disconnect multiple sensors and test separately. 3. Keep all people completely out of the detection pattern to make sure the sensor is not detecting them. 4.
Technical Tips: Lights Do Not Turn On 1. Check that lamps and fixtures work. Compare wiring to the Wiring Diagram in this manual. Check that the power is on. 2. If installing during daylight, remember that after power is turned on, the sensor will provide 5 minutes of Test Time. After 5 minutes, the sensor will switch to Automatic Mode and will not work during daylight if the photocell control is turned to night-only (moon) position.
Technical Tips: Range Appears Limited 1. Check that the sensor is level from side to side and pointed at desired area. If unit is tilted, part of the Detection Zone may be high in the air over people’s heads. 3. Check that movement is not directly towards sensor. Sensor will see movement across its pattern more quickly. To fix, move sensor. WRONG! Solution: Position sensor exactly level from side to side. 4. Check that movement far away and directly towards sensor is not entirely within one zone.
Limited Warranty Your STEALTH will be replaced or repaired, at our option, if it proves to be defective in worksmanship or materials within ten years from the date of original purchase. For repair or replacement, return the product, freight prepaid and insured, to: RAB Lighting 170 Ludlow Avenue Northvale, NJ 07647 The STEALTH should be packed carefully. Please include your sales receipt and a description of the problem.
Contents: STL200-LED • Indoor Switchplate Label • Wire Nuts (3) Easy Installation & Product Help ©2016 RAB LIGHTING Inc. Northvale, New Jersey 07647 USA STL200LED IN 0616 12 Tech Help Line Call our experts 888 RAB-1000 rabweb.com Visit our website for product info email Answered promptly sales@rabweb.
STEALTH STL200-LED/277 Installation Manual STL200-LED/277 Specifications: Switching Capacity: 8 amps Voltage: 277 volts 300W on LED fixture Detection Pattern: 50’ x 2000 Time Adjustment: 5 seconds to 12 minutes Power Consumption: 1 watt Surge Protection: I.E.C.
CAUTIONS: TURN OFF ALL POWER AT CIRCUIT BREAKER/FUSE PANEL. • Read entire Installation Manual before proceeding. • All wiring should comply with local electrical codes and requires a qualified electrician • The total lighting load connected to a STEALTH must not exceed 8 amps (300W on LED fixture). To switch more wattage an electrician can install a relay. • Line Carrier Remote Control Systems such as X-10, Levitron or Radio Shack are incompatible with sensors and cause false activations.
How does the STEALTH work? STEALTH’s infrared sensor “sees” small temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically. It welcomes visitors and may deter intruders. How long do the lights stay on? Lights remain on as long as there is movement within the protection zone. Once the zone is vacated, lights can be adjusted to remain on from approximately 5 seconds-12 minutes.
Choosing a Location • Choose a location so that the sensor can “see” all paths of movement. • The sensor may be wall or ceiling mounted. • As distance from the sensor increases, it takes more movement to be detected. For example: a half-step will register at ten feet, but not at 40 feet. 40 feet will need several steps for detection. How does the LED Detection Indicator work? The red LED above the lens shows the logic state of the sensor.
Wiring Diagrams Multiple Fixtures Basic Wiring Diagram White Ground Power In Red Black Sensor Basic Kit Wiring Diagram Note: Pigtail is only used to switch remote or additional light fixtures. Red (pigtail) Red Black Switchplate Label Black Power In White Ground • Multiple fixtures may be wired to a single sensor • To handle loads greater than 300 watts, a qualified electrician should install a relay. Switchplate label has self-adhesive backing.
Aiming and Walk Testing Walk Test: The purpose of the Walk Test is to check and adjust the coverage pattern. STEALTH has a 5 minute Test Period which allows the sensor to be aimed and walk-tested day or night. If you require 5 more minutes of Test Time, turn the power off for at least 10 seconds and back on again. During the Test Period, the sensor will keep lights on for 5 seconds each time it detects movement in its Detection Zone. The sensor will change to Automatic Mode after 5 minutes of testing. 3.
Technical Tips: Lights Turn On for Unknown Reasons 1. Lights may turn on occasionally during rain, snow and windstorms because the sensor detects changes in temperature. Solution: mount sensor in protected area. 3. You may not be aware of animals triggering the sensor. Create an “Animal Alley” by aiming sensor or masking the lower portion of the lens with opaque weatherproof tape to reduce triggering. 10’ “Animal Alley” 50’ 4.
Technical Tips: Lights Do Not Turn Off 1. Make sure the sensor is not in Manual Override Mode. Turn power OFF for 10 seconds and then ON again. Sensor will be in Test Mode for approximately 5 minutes, then it will switch to Auto Mode with lights off, ready to detect movement. 3. Make sure sensor and lights are mounted firmly and do not move, even slightly, when touched. If they move, tighten all screws. 2.
Technical Tips: Lights Turn On and Off Incorrectly 1. Make sure the sensor is installed on its own dedicated circuit, free of motor loads such as HVAC equiptment, kitchen appliances, or garage door openers. 2. It is not recommended to wire sensors in parallel. More than one sensor wired together makes them difficult to troubleshoot. Disconnect multiple sensors and test separately. 3. Keep all people completely out of the detection pattern to make sure the sensor is not detecting them. 4.
Technical Tips: Lights Do Not Turn On 1. Check that lamps and fixtures work. Compare wiring to the Wiring Diagram in this manual. Check that the power is on. 2. If installing during daylight, remember that after power is turned on, the sensor will provide 5 minutes of Test Time. After 5 minutes, the sensor will switch to Automatic Mode and will not work during daylight if the photocell control is turned to night-only (moon) position.
Technical Tips: Range Appears Limited 1. Check that the sensor is level from side to side and pointed at desired area. If unit is tilted, part of the Detection Zone may be high in the air over people’s heads. 3. Check that movement is not directly towards sensor. Sensor will see movement across its pattern more quickly. To fix, move sensor. WRONG! Solution: Position sensor exactly level from side to side. 4. Check that movement far away and directly towards sensor is not entirely within one zone.
Limited Warranty Your STEALTH will be replaced or repaired, at our option, if it proves to be defective in worksmanship or materials within ten years from the date of original purchase. For repair or replacement, return the product, freight prepaid and insured, to: RAB Lighting 170 Ludlow Avenue Northvale, NJ 07647 The STEALTH should be packed carefully. Please include your sales receipt and a description of the problem.
Contents: STL200-LED/277 • Indoor Switchplate Label • Wire Nuts (3) Easy Installation & Product Help ©2016 RAB LIGHTING Inc. Northvale, New Jersey 07647 USA Tech Help Line Call our experts 888 RAB-1000 STL200LED/277V IN 0216 12 rabweb.com Visit our website for product info email Answered promptly sales@rabweb.
STEALTH STL200-LED Installation Manual STL200-LED Specifications: Switching Capacity: 8 amps Voltage: 120 volts 300W on LED fixture Detection Pattern: 50’ x 2000 Time Adjustment: 5 seconds to 12 minutes Power Consumption: 1 watt Surge Protection: I.E.C.
CAUTIONS: TURN OFF ALL POWER AT CIRCUIT BREAKER/FUSE PANEL. • Read entire Installation Manual before proceeding. • All wiring should comply with local electrical codes and requires a qualified electrician • The total lighting load connected to a STEALTH must not exceed 8 amps (300W on LED fixture). To switch more wattage an electrician can install a relay. • Line Carrier Remote Control Systems such as X-10, Levitron or Radio Shack are incompatible with sensors and cause false activations.
How does the STEALTH work? STEALTH’s infrared sensor “sees” small temperature changes caused by the motion of people or cars within its protection zone and turns on lights automatically. It welcomes visitors and may deter intruders. How long do the lights stay on? Lights remain on as long as there is movement within the protection zone. Once the zone is vacated, lights can be adjusted to remain on from approximately 5 seconds-12 minutes.
Choosing a Location • Choose a location so that the sensor can “see” all paths of movement. • The sensor may be wall or ceiling mounted. • As distance from the sensor increases, it takes more movement to be detected. For example: a half-step will register at ten feet, but not at 40 feet. 40 feet will need several steps for detection. How does the LED Detection Indicator work? The red LED above the lens shows the logic state of the sensor.
Wiring Diagrams Multiple Fixtures Basic Wiring Diagram White Ground Power In Red Black Sensor Basic Kit Wiring Diagram Note: Pigtail is only used to switch remote or additional light fixtures. Red (pigtail) Red Black Switchplate Label Black Power In White Ground • Multiple fixtures may be wired to a single sensor • To handle loads greater than 300 watts, a qualified electrician should install a relay. Switchplate label has self-adhesive backing.
Aiming and Walk Testing Walk Test: The purpose of the Walk Test is to check and adjust the coverage pattern. STEALTH has a 5 minute Test Period which allows the sensor to be aimed and walk-tested day or night. If you require 5 more minutes of Test Time, turn the power off for at least 10 seconds and back on again. During the Test Period, the sensor will keep lights on for 5 seconds each time it detects movement in its Detection Zone. The sensor will change to Automatic Mode after 5 minutes of testing. 3.
Technical Tips: Lights Turn On for Unknown Reasons 1. Lights may turn on occasionally during rain, snow and windstorms because the sensor detects changes in temperature. Solution: mount sensor in protected area. 3. You may not be aware of animals triggering the sensor. Create an “Animal Alley” by aiming sensor or masking the lower portion of the lens with opaque weatherproof tape to reduce triggering. 10’ “Animal Alley” 50’ 4.
Technical Tips: Lights Do Not Turn Off 1. Make sure the sensor is not in Manual Override Mode. Turn power OFF for 10 seconds and then ON again. Sensor will be in Test Mode for approximately 5 minutes, then it will switch to Auto Mode with lights off, ready to detect movement. 3. Make sure sensor and lights are mounted firmly and do not move, even slightly, when touched. If they move, tighten all screws. 2.
Technical Tips: Lights Turn On and Off Incorrectly 1. Make sure the sensor is installed on its own dedicated circuit, free of motor loads such as HVAC equiptment, kitchen appliances, or garage door openers. 2. It is not recommended to wire sensors in parallel. More than one sensor wired together makes them difficult to troubleshoot. Disconnect multiple sensors and test separately. 3. Keep all people completely out of the detection pattern to make sure the sensor is not detecting them. 4.
Technical Tips: Lights Do Not Turn On 1. Check that lamps and fixtures work. Compare wiring to the Wiring Diagram in this manual. Check that the power is on. 2. If installing during daylight, remember that after power is turned on, the sensor will provide 5 minutes of Test Time. After 5 minutes, the sensor will switch to Automatic Mode and will not work during daylight if the photocell control is turned to night-only (moon) position.
Technical Tips: Range Appears Limited 1. Check that the sensor is level from side to side and pointed at desired area. If unit is tilted, part of the Detection Zone may be high in the air over people’s heads. 3. Check that movement is not directly towards sensor. Sensor will see movement across its pattern more quickly. To fix, move sensor. WRONG! Solution: Position sensor exactly level from side to side. 4. Check that movement far away and directly towards sensor is not entirely within one zone.
Limited Warranty Your STEALTH will be replaced or repaired, at our option, if it proves to be defective in worksmanship or materials within ten years from the date of original purchase. For repair or replacement, return the product, freight prepaid and insured, to: RAB Lighting 170 Ludlow Avenue Northvale, NJ 07647 The STEALTH should be packed carefully. Please include your sales receipt and a description of the problem.
Contents: STL200-LED • Indoor Switchplate Label • Wire Nuts (3) Easy Installation & Product Help ©2016 RAB LIGHTING Inc. Northvale, New Jersey 07647 USA STL200LED IN 0616 12 Tech Help Line Call our experts 888 RAB-1000 rabweb.com Visit our website for product info email Answered promptly sales@rabweb.
