Cut Sheet

ManualsBrandsRAB ManualsLED VandalproofVandalproof Canopy 10W Cool LED 120-277V W/ Flat Lens Bronze

VANLED INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required

for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON

FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

CEILING MOUNTING

The xture is suitable for outdoor applications in wet

locations.

1. Remove Door by loosening (4) Captive Screws.

2. Remove Reector/ LED Assembly by loosening (4)

Reector/ LED Screws.

3. Hang Reector/ LED Assembly by Tether Cable.

4. Knock out appropriate Slots as marked in Fig. 2, by

loosening Screws (2) on Access Plate and secure to

junction box (not supplied). Check gasket is fully sealed.

5. Mount Ceiling Mounting Box to ceiling by drilling

out (4) Drill Locations as marked in Fig. 2. Use the

appropriate mounting hardware for the mounting

surface. Be sure gasket is properly seated.

6. Feed xture wires through the Access Plate or through

one of the Plugs (4) to make electrical splices in junction

box. Use appropriate UL approved wire connectors as

required by code to complete wiring.

7. Re-assemble Reector/ LED Assembly and Door. Be

careful not to pinch wires.

8. Tighten all screws.

9. Use silicone or teon tape on all Plugs and on the

threads of all conduit entry points. If outdoor surface

is irregular , use caulk to seal any gaps around Ceiling

Mounting Box.

VANLED - Drop Lens VANLED - Flat Lens

Ceiling Mounting Box

CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened

rmly. Apply weatherproof silicone sealant around the edge of the Ceiling Mounting Box and/or Junction Box. This is

especially important with an uneven ceiling surface. Silicone all plugs and unused conduit entries.

Plugs (4)

Access Plate

Screws (2)

Tether Cable

Reector/ LED

Assembly

Reector/ LED

Screws (4)

Captive

Screws (4)

Door

Fig. 1

Summary of content (2 pages)

PAGE 1
VANLED INSTALLATION INSTRUCTIONS TM Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com VANLED - Drop Lens VANLED - Flat Lens IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.
PAGE 2
VANLED INSTALLATION INSTRUCTIONS TM Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com ON-OFF WIRING DRILL LOCATION Universal voltage driver permits operation at 120V thru 277V, 50 or 60 Hz. Units ordered with (/480V) suffix are 480V, 50Hz or 60Hz. For Non-Dimming, follow the wiring directions in fig. 3. 1.