Cut Sheet

ManualsBrandsRAB ManualsHID & CFL Wall PacksWALL 80W WARM DIM BRONZE

WPLED 52W/ 80W INSTALLATION INSTRUCTIONS

Thank you for buying RAB lighting xtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments.

Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com

IMPORTANT

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

RAB xtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding

is required for safety. THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A

PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED.

WARNING: Make certain power is OFF before installing or maintaining xture. No user serviceable parts inside.

MOUNTING TO A WALL

1. Orient Wall Mount Box such that ‘TOP’ is pointing up.

2. Feed supply wires through Wall Mount Box Gasket

into Wall Mount Box through Silicone Wiring Plug, if

not using conduit/ connectors.

3. Secure Wall Mount Box to a sturdy mounting surface.

Use appropriate mounting hardware such as lag bolts

and anchors with washers suitable for the mounting

surface. A Leveling Bubble is provided to level xture.

4. Silicone around the edge of Wall Mount Box Gasket

and/ or junction box.

5. Check that Gasket is fully sealed.

6. Slide the stainless steel Tether from the xture into the

Key Hole Slot for hands free wiring.

7. Wire the xture using UL listed wire connectors

according to NEC and local codes.

8. Place wired xture over the Wall Mount Box and

tighten the Top Screws. Then tighten the Lower

Screws.

9. Tighten Close Up Plugs and apply weatherproof

silicone sealant to all unused conduit entry points.

WPLED52/ WPLED80

Standard (15 Deg)

WPLEDC52/ WPLEDC80

Cuto (7.5 Deg)

WPLEDFC52/ WPLEDFC80

Full Cuto (0 Deg)

CAUTION: For proper weatherproof function all gaskets must be seated properly and all screws inserted and tightened

rmly. Apply weatherproof silicone sealant around the edge of the Wall Box and/or Junction Box. This is especially

important with an uneven wall surface. Silicone all plugs and unused conduit entries.

WPLED104 WALLMOUNT

RAB LIGHTING INC

9 JANUARY 2015

Wall Mount Box

Top Screws

Lower Screws

Close Up

Plugs (4)

Gasket

Tether

Silicone

Wiring Plug

Wall Mount Box

Gasket

Key Hole Slot

Leveling

Bubble

4.58”

116.2mm

4.97”

126.3mm

1.30”

33mm

4.58”

116.2mm

4.97”

126.3mm

Summary of content (3 pages)

PAGE 1
® WPLED 52W/ 80W INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com WPLED52/ WPLED80 Standard (15 Deg) WPLEDC52/ WPLEDC80 Cutoff (7.5 Deg) WPLEDFC52/ WPLEDFC80 Full Cutoff (0 Deg) IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.
PAGE 2
® WPLED 52W/ 80W INSTALLATION INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.
PAGE 3
ALED® WPLED® 52W/ 80W BILEVEL INSTRUCTIONS Thank you for buying RAB lighting fixtures. Our goal is to design the best quality products to get the job done right. We’d like to hear your comments. Call the Marketing Department at 888-RAB-1000 or email: marketing@rabweb.com IMPORTANT READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. Fixtures must be wired in accordance with the National Electrical Code and all applicable local codes.