User`s manual

162 eDisplay (OP7200)
K
keypad
function calls
keyConfig ......................96
keyGet ...........................97
keyInit ............................96
keypadDef .....................98
keyProcess .....................97
keyScan .........................98
L
LCD
function calls
glBlankScreen ...............79
glBlock ..........................81
glBuffUnlock .................78
glFillCircle .....................83
glFillPolygon .................82
glFillVPolygon ..............82
glFontCharAddr .............85
glGetBrushType ............80
glGetPfStep ...................84
glHScroll .......................89
glInit ..............................78
glLeft1 ...........................88
glMenu ...........................76
glMenuClear ..................77
glMenuInit .....................75
glPlotCircle ....................83
glPlotDot .......................80
glPlotLine ......................80
glPlotPolygon ................81
glPlotVPolygon .............82
glPrintf ...........................84
glPutChar .......................85
glPutFont .......................85
glRefreshMenu ..............76
glRight1 .........................88
glSetPfStep ....................84
glSwap ...........................78
glUp1 .............................89
glVScroll .......................90
glXFontInit ....................83
glXGetBitmap ...............91
glXGetFastmap ..............92
glXPutBitmap ................90
glXPutFastmap ..............91
TextBorder .....................92
TextBorderInit ...............92
TextCursorLocation .......87
TextGotoXY ..................86
TextMaxChars ...............93
TextPrintf .......................88
TextPutChar ...................87
TextWindowFrame ........86
LCD controller ................40, 50
handling applications devel-
oped for older chip ........50
identifying new part ..........40
LCD screen control
function calls
glAnimation ...................94
glBackLight ...................94
glDispOnOff ..................95
glRealtime .....................94
glSetContrast .................95
M
memory .................................39
models .....................................2
OP7200 ................................2
OP7210 ................................2
mounting and installation
.............................123, 124
O
OP7200
introduction .........................1
overlay
cleaning instructions ........125
P
peripheral cards .......................5
connection to master 151, 152
physical mounting ...............130
pinout
Ethernet port ......................37
OP7200 headers ................18
power management .............139
power supply ...................3, 139
backup battery circuit ......143
battery backup .................141
chip select circuit .............145
connections ........................10
switching voltage regulator ...
139
VRAM switch .................144
power-up
demonstration program .....11
programming
flash vs. RAM ...................47
programming cable ..............3
programming port ..............38
programming cable .................3
connections ........................12
PROG connector ...............44
programming port .................38
R
Rabbit 2000
parallel ports ....................135
RabbitNet ................................5
Ethernet cables to connect
peripheral cards ...151, 152
function calls
rn_comm_status ...........160
rn_device .....................155
rn_echo ........................156
rn_find .........................155
rn_hitwd .......................159
rn_init ..........................154
rn_read .........................157
rn_reset ........................157
rn_rst_status .................159
rn_write .......................156
general description ..........151
hardware configuration .....36
peripheral cards ...............152
physical implementation .153
RabbitNet port ...................36
use of Serial Port B ...........36
RabbitNet port
function calls ...................111
rn_sp_close ..................111
rn_sp_disable ...............112
rn_sp_enable ................112
rn_sp_info ....................111
macros .............................111
real-time clock
how to set ..........................15
reset .......................................10
hardware ............................10
reset generator .................144
RS-485 network ....................34
termination and bias resis-
tors ................................35