Installation & Assembly

Pot Rack
ASSEMBLY INSTRUCTIONS:
Be certain that barrel nuts and bolts screw
together easily BEFORE beginning assembly.
1. On a table lay out all parts as shown in the exploded view above.
2. Temporarily connect two Bookshelf ends (9) and the side bar(3A) by
inserting a barrel nut and bolt (28A, 28B) through the top hole at each of
four corners. This is the front of the rack. This will cause body of pot rack
to stand on edge. Be certain side bar (3A) is on the INSIDE when
connected. TIP! It is easiest to attach the pot rack parts when you insert
the barrel nut (28B) from the INSIDE of the pot rack body, then screw the
barrel bolt (28A) into 28B from the OUTSIDE.
3. Now remove the barrel bolt (28A) from one of the corners, keeping
barrel nut (28B) in position. Place a curve arm (22) (2-hole end) on the OUTSIDE of the body. Align the three pieces: (side bar 3A) on inside,
bookshelf end piece (9) in middle, arm (22) on outside), and reinsert the barrel bolt (28A) through the upper hole from the OUT- SIDE. Repeat
for lower hole. Do not tighten barrel bolts firmly until all bolts are in place.
4. Repeat STEP THREE for remaining arm.
5. Place assembled rack squarely on table and adjust all parts to be certain they are level and straight. Then tighten all bolts firmly.
Remember the back bar (3D) is not attached until the rack is installed on the wall.
6. Note the small holes located in the center of the flat section of each shelf bracket. Two set screws (18E) will be driven through them to
secure the Wood shelf to the brackets. Center the Wood shelf on top of the brackets (now fixed in position) then with a pencil mark the two
set screw points on the un- der side of the bracket. Pre-drill the marks (or tap a starter hole with a hammer and a small nail) then drive set
screws (18E) into Wood to secure shelf.
7. After the shelf is assembled, and after bookshelf rack is squared and tightened, the distance from center of the holes at top of the arms to
the center of upper holes in back bar should be 9 3/4”. The width between upper holes is 20-3/4”. Use these when determining location of
rack on the wall in the installation section. NOTE: Grid and brackets will be added AFTER the rack is attached to the wall.
INSTALLATION INSTRUCTIONS
Provided: Installation hardware (anchors, bolts, wall screws and red sleeves)
You will need: level, tape measure, pencil, electric drill and ½” and 1/8” drill bits, hammer and nail.
1. On the wall, mark the four points 20-3/4” long by 9-3/4” high where the top of rack arms and back bar will attach. Then tap a small nail
through each mark to be certain a joist is not in the way
2. RACK IT UP!’s drywall toggles eliminate the need to bolt your pot rack to a stud. You can install your rack securely into drywall.
INSTALL IN WOOD:
If you need to install one or both sides of your rack in wood, use as many of the four wall screws (30A) included, but
without a red sleeve.
PAINTABLE: Want a different color? The finish on this pot rack can be spray painted any color. We recommend Rustoleum “Hammered”
colors for their metal-like finishes, however any quality spray-can paint may be used. See a paint retailer for guidance
WARNING: It is important that your pot rack is assembled correctly. If the unit is assembled or used incorrectly, it could become unstable
and collapse, possibly causing injury.
LIMITED WARRANTY: This product is warranted to be free of material defects, other than that from normal use, for a period of one year
from the date of purchase. Customer's exclusive remedy shall be the repair or replacement of the defective product and shall be subject to
the following conditions: (1) notice of any defect is received by Rack It Up within the warranty period and (2) customer returns the
defective product, postage prepaid within 20 days following a return authorization number
(which may be obtained by telephoning the number at the top of this instructions) being provided to the customer by Rack It Up. There are
no other warranties, expressed or implied. There are no warranties of merchantability or fitness for a particular purpose. RACK IT UP
specifically disclaims any and all incidental or consequential damages arising out of the purchase or use of RACK IT UP’S products.
Item No.
Description
Qty
Item No.
Description
Qty.
3A
Side bar w/4 through holes
1
28A
Barrel screw
5
3D
Back bar w 2 through & 2 tap holes
1
28B
Barrel screw
5
7B
Grid bracket for bookshelf
3
29
Wood shelf
1
8B
Grid 8” x 22’ x 2” x 2”
1
35
(L) bracket
2
9
Bookshelf end piece
2
Installation Hardware
18A
1/4” button head 1/4 x 20 /1/4
2
19C
Button head screw 1/4 x 20 x 2”
2
18E
#6 Wood screw 1/2”
2
26A
5/32 hex wrench
2
22
Bookshelf curved arm (long)
2
30A
Wall screw
2
25A
Pot hook straight
4
30B
Wall sleeve
2
25B
Pot hook angled
4
27A
1/4” Toggle
2