User's Manual

ManualsBrandsRacom ManualsElectronicsISM Transmitter

Table Of Contents

RAy2 Microwave Link
Table of Contents
Important Notice
Quick guide
List of documentation
1. RAy2 – Microwave Link
2. Implementation Notes
- 2.1. Link calculation
- 2.2. Example of microwave link design
3. Product
- 3.1. Mounting
- 3.2. Connectors
- 3.3. Power supply
- 3.4. Status LEDs
- 3.5. Technical parameters
- 3.6. Dimensions
- 3.7. Ordering codes
4. Accessories
- 4.1. Overview
- 4.2. Details
5. Step-by-step Guide
- 5.1. Service access
- 5.2. Basic link configuration
- 5.3. Link test
6. Installation
- 6.1. Line of sight test
- 6.2. Antenna mounting
- 6.3. Connectors assembly
- 6.4. Grounding
- 6.5. Start up
7. Configuration
- 7.1. Introduction
- 7.2. Status bar
- 7.3. Status
- 7.4. Link settings
- 7.5. Switch settings
- 7.6. Tools
- 7.7. Help
8. Command Line Interface
- 8.1. Connection via CLI
- 8.2. Working with CLI
  - 8.2.1. SSH keys
  - 8.2.2. Scripts
- 8.3. Configuration with CLI
9. Troubleshooting
10. Technical parameters
- 10.1. General parameters
  - 10.1.1. Technical parameters overview
  - 10.1.2. Link speed
- 10.2. Nominal frequency tables description
- 10.3. RAy2-10 parameters
- 10.4. RAy2-11 A,B parameters
- 10.5. RAy2-11 C,D parameters
- 10.6. RAy2-17 parameters
- 10.7. RAy2-18 parameters
- 10.8. RAy2-24 parameters
11. Safety, environment, licensing
- 11.1. Frequency
- 11.2. Safety distance
- 11.3. Professional installation
- 11.4. RoHS and WEEE compliance
- 11.5. Liability for Defects and Safety Instructions
- 11.6. Important Notifications
- 11.7. Warranty
- 11.8. Declaration of Conformity
- 11.9. FCC authorization of transmitters
- 11.10. Country of Origin Declaration
Appendix A. Antenna dimensions
Appendix B. Rain zone map
Appendix C. IP address in the PC (Windows XP)
Appendix D. IP address in the PC (Windows 7)
Appendix E. IP address in the PC (Windows 8)
Appendix F. SSH key generation
Appendix G. Https certificate
Appendix H. Unit block diagrams
Index
Appendix I. Revision History

Assembly procedure:

Fig. 6.25: Bushing and connector assembly

Fig. 6.26: Bushing incl. lengthening and connector assembly

• Put on the cable: the nut No.1, rubber sealing No.2, bushing No.3 and O-ring No.4.

• Attach the appropriate connector No.5 to the cable.

• Plug the connector No.5 into the RAy2 unit.

• Screw the bushing No.3 with the sealing O-ring into the RAy2 unit.

• Move the rubber sealing No.2 along the cable to fit in the bushing. Screw the nut No.1 on bushing

No.3.

• (If you use extension ring No. 6 lubricate its thread with grease.)

Disassembly procedure:

• Release the nut No.1

• Remove the rubber sealing No.2

• Unscrew the bushing No.3 with O-ring No.4 (and extension No.6 with O-ring No.7).

• Remove the connector.

Installation