User's Manual
Table Of Contents
- RipEX2 Radio modem & Router
- Table of Contents
- Important Notice
- 1. Quick guide
- 2. Product
- 3. Accessories
- 4. Installation
- 5. RipEX2 in detail
- 6. Web interface
- 7. Settings
- 7.1. Interfaces
- 7.1.1. Ethernet
- 7.1.2. Radio
- 7.1.3. COM
- 7.1.4. Terminal servers
- 7.1.5. Cellular
- 7.2. Routing
- 7.2.1. Static
- 7.2.2. OSPF
- 7.2.2.1. Description
- 7.2.2.2. Common - Common settings
- 7.2.2.3. Network - Areas and interfaces - Areas
- 7.2.2.4. Network - Areas and interfaces - Interfaces
- 7.2.2.5. Network - Areas and interfaces - Neighbors
- 7.2.2.6. Network - Areas and interfaces - Networks
- 7.2.2.7. Static rules
- 7.2.2.8. Import filter
- 7.2.2.9. Export filter
- 7.2.3. BGP
- 7.3. Firewall
- 7.4. VPN
- 7.5. Security
- 7.6. Device
- 7.7. Advanced
- 7.1. Interfaces
- 8. Diagnostics
- 9. Technical parameters
- 10. Safety, regulations, warranty
- 10.1. Frequency
- 10.2. Safety distance
- 10.3. High temperature
- 10.4. Battery disposal
- 10.5. Instructions for Safe Operation of Equipment
- 10.6. SW license
- 10.7. EU Compliance
- 10.8. Compliance Federal Communications Commission and Innovation, Science and Economic Development Canada
- 10.9. Compliance ANATEL Brasil
- 10.10. Warranty
- 10.11. RipEX2 Availability and service life time
- 10.12. RipEX2 maintenance
- Appendix A. Abbreviations
- Index
- Revision History
• Active
List box {On; Off}, default = "Off"
Enables / disables the interface.
• Interface
List box {list of existing OSPF interfaces}
OSPF interface the neighbor belongs to. The interface – Note value is used when defined. The inter-
face – Interface value is used otherwise.
• IP
IP address of the neighbor.
• Note
Informational note
7.2.2.6. Network - Areas and interfaces - Networks
The Networks table modifies networks announced out of the area. It enables partial networks aggreg-
ation into the common prefixes or specific network hiding. Maximum number of rules is 256.
• Active
List box {On; Off}, default = "Off"
Enables / disables the interface.
• Area
List box {list of existing OSPF areas}
OSPF area the record belongs to.
• IP / mask
IP address and mask of the range (i.e. network) which will be aggregated or hidden.
• Action
List box {Aggregate; Hide}, default = "Aggregate"
○ Aggregate – small network prefixes will be exported from this area aggregated into this range
(defined by IP / mask)
○ Hide – this network prefix will be hidden and will not be exported
Example:
Area 0.0.0.1 exports two subnets: 192.168.1.0/24 and 192.168.2.0/24. Area border router between
Area 0.0.0.1 and 0.0.0.0 defines a rule for network aggregation: 192.168.0.0/16. As a result of this,
the area border router announces to the area 0.0.0.0 only one route 192.168.0.0/16 instead of the
two individual routes.
• Note
Informational note
7.2.2.7. Static rules
Pre-defined static routing rules to be exported over the OSPF protocol. Maximum number of rules is
256.
• Active
RipEX2 Radio modem & Router – © RACOM s.r.o.92
Settings