User's Manual
Table Of Contents
- RipEX2 Radio modem & Router
- Table of Contents
- Important Notice
- 1. Quick guide
- 2. Product
- 3. Accessories
- 4. Installation
- 5. RipEX2 in detail
- 6. Web interface
- 7. Settings
- 7.1. Interfaces
- 7.1.1. Ethernet
- 7.1.2. Radio
- 7.1.3. COM
- 7.1.4. Terminal servers
- 7.1.5. Cellular
- 7.2. Routing
- 7.2.1. Static
- 7.2.2. OSPF
- 7.2.2.1. Description
- 7.2.2.2. Common - Common settings
- 7.2.2.3. Network - Areas and interfaces - Areas
- 7.2.2.4. Network - Areas and interfaces - Interfaces
- 7.2.2.5. Network - Areas and interfaces - Neighbors
- 7.2.2.6. Network - Areas and interfaces - Networks
- 7.2.2.7. Static rules
- 7.2.2.8. Import filter
- 7.2.2.9. Export filter
- 7.2.3. BGP
- 7.3. Firewall
- 7.4. VPN
- 7.5. Security
- 7.6. Device
- 7.7. Advanced
- 7.1. Interfaces
- 8. Diagnostics
- 9. Technical parameters
- 10. Safety, regulations, warranty
- 10.1. Frequency
- 10.2. Safety distance
- 10.3. High temperature
- 10.4. Battery disposal
- 10.5. Instructions for Safe Operation of Equipment
- 10.6. SW license
- 10.7. EU Compliance
- 10.8. Compliance Federal Communications Commission and Innovation, Science and Economic Development Canada
- 10.9. Compliance ANATEL Brasil
- 10.10. Warranty
- 10.11. RipEX2 Availability and service life time
- 10.12. RipEX2 maintenance
- Appendix A. Abbreviations
- Index
- Revision History
Number {0 – 2
32
-1}, default = 10
The cost of connection to this neighbor. The higher the number the higher the cost. It enables to
make decisions inside the router between multiple paths from the same neighbor.
• Next hop self
List box {Off; Always; Internal; External}, default = "Off"
Defines it the exported routing rules should have ‘next hop’ addresses overwritten to the address of
this router. "Internal" overwrites only the rules from the local AS. "External" overwrites only the rules
from the other AS.
7.2.3.4. Static rules
Pre-defined static routing rules to be exported over the BGP protocol. Maximum number of rules is
256.
• Active
List box {On; Off}, default = "Off"
Enables / disables the static routing rule.
• Destination IP / Destination mask
IP address, default = 0.0.0.0/32
IP address and mask defining the exported routing rule destination address range.
• Note
Informational note.
7.2.3.5. Import IGP filter
Import IGP filter [PP1] rules. The order of rules matters. Maximum number of filter rules is 256.
• Filter policy
List box {Accept; Reject}, default = "Reject"
Defines what action is taken on the routing rules which were not captured (i.e. fallback) in the Import
IGP filter.
• Active
List box {On; Off}, default = "On"
Enables / disables the filter rule.
• Note
Informational note.
• Filter network
List box {Off; Match; Not match}, default = "Off"
Selects a method of the routing rule destination range comparison.
• Network IP / Network mask
IP address, default = 0.0.0.0/0
IP address and mask defines the network prefix to be compared
• Mask from
Number {0 – 32}, default = 0
• Mask to
99© RACOM s.r.o. – RipEX2 Radio modem & Router
Settings