Owner’s Manual
Important Note To Parents About Safe Riding Your child's safety will depend on your commitment to always provide a safe riding environment and a properly maintained vehicle. As with any moving vehicle there are possible safety risks; be sure to heed to the following precautions. 1. Always equip your child with suitable protective gear and riding apparel. Be sure he or she always wears a helmet, over-the-ankle footwear, eye protection, long pants, and a long-sleeved shirt while riding. 2.
Safety Precautions 1. 2. 3. 4. 5. Review all the instructions carefully before operations. Follow all rules and regulations in your area for operating an electric scooter. Do not allow others to use the scooter without proper instructions. Ride only in good weather and on smooth surfaces. Remember to always operate your scooter with the proper safety gear and helmet. Operating Points 1. 2. Turn the power switch to the ON ( | ) position before starting the scooter.
M. List of Parts Throttle - A Brake Handle - B Airless Tires - C Brake Cable - D Deck - E Front Fork - F Hub/Rim - G Kickstand - H Folding Quick Release – I Handle Bar Quick Release - J Rear Tire Assembly - K Switch Box - L Tool Kit - M 1. Allen Wrench (3 different sizes) 2. Wrench (2) 3. Screw Driver 4.
Assembly Instructions 1. Carefully take your scooter out of the box. 2. Assemble the Handle Bar. ** See Photo’s on Page 6 a. Lift Handle Bar up. Do not put any pressure on the front tire while raising the Handle Bar. (See Figure A) b. Tighten the Folding Quick Release bolt by turning it clockwise. (See Figure B & C) c. Push the Folding Quick Release lever down to lock the Handle Bar into place. d.
(a) (b) (c) (d) 6
Charging 1. 2. 3. 4. 5. Turn Power Switch in the ‘off’ position. Do not plug the charger into the outlet first, for safety reasons plug the charger cord into the scooter first, then into a 110 V outlet. Charge your scooter for 6-8 hours. The LED will be red during charging and once it is fully complete the LED will turn to green. Do not overcharge you battery this may limit the life of your battery. Unplug after 8 hours to avoid overheating. Charge unit when a yellow or red light appears and every 90 days.
Procedure for changing rear tire of ZZ Cruiser • Tools Required: - Phillips screwdriver - 8mm wrench - 2 x 16mm wrench Ensure power switch is in the "off" position before beginning any work on the scooter. Fig. 1 Step 1) Remove the 3 screws from the deck, use the Medium size Allen wrench to remove screws as shown in Figure 1. Lift the deck. Fig. 2 Step 2) Remove screw holding brake shield in place (see fig. 2) located next to the left side of the rear tire.
Fig. 3 Step 3.) Remove the axle nut located on the right side of the rear tire as seen in Fig 3. Fig. 4 Step 4.) Loosen the brake adjustment bolt as seen in Fig 4. Do not completely remove this bolt. It should loosen to the point where the line traveling through the “brake spring” can be removed. Next remove the drive belt from the tire sprocket. Once this has been completed, the rear tire and hub can be removed from the scooter.
Fig. 5 Step 5.) Remove the axle bolt from the rear wheel; take not of where the spacers are located. Fig. 6 Step 6.) Remove the Allen bolts from the rim of the tire; you must first cut ½” off of the medium size Allen wrench (use hack saw). The rim will split into 2 pieces. Once apart, replace the old tire with the brand new tire you have just received. Reassemble the rim back onto the tire.
Fig. 7 Step 7.) Place the brake shield back on the wheel’s slide axle brake into the tire and remember to place the pacer between the brake shield and brake drum. Fig. 8 Step 8.) Next place the wheel hub back into the rear fork and reinstall the drive belt. Retighten the axle bolts.
Fig. 9 Step 9.) Insert the “L”-shaped bracket onto the brake shield. The hole for this bracket is located farthest from the wheel axle on the bracket itself. The bracket should be placed on the “tire-side” of the shield (as opposed to the outer side). (Wheel shown as removed to better display “L”-shaped bracket). Next, place the brake spring back into its original setting as seen in Fig 9.
Troubleshooting Chart Problem The power light by the on/off switch does not light up when the scooter is turned on. 1. 2. Cause Battery is discharged. Loose connection inside the scooter. 1. 2. Solution Recharge your scooter. Remove (3) screws that hold the deck on and remove the deck. Visually inspect all wire connections making sure there are no loose wires, reconnecting those that are. Replace the Throttle Handle. Call Customer Service at (800) 498-8455 to order a new Throttle.
List of Parts Throttle (1) Small Star Screws (2) Lock Washers (2) Drive Belt (1) Controller (1) Brake Handle (1) Airless Tires (2) Valve Extension (1) Brake Cable (1) Deck (1) Front Fork (1) Front Tire Assembly (1) Hub/Rim (2) Kickstand (1) Motor 300 Watt (1) Folding Quick Release (1) Handle Bar Quick Release (1) Rear Tire Assembly (1) Switch Box (1) Tool Kit (1) 1. Allen Wrench (3 different sizes) 2. Wrench (2) 3. Screw Driver (1) 4.
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING THE USE OF THIS SCOOTER.
Warranty. Rad2Go warrants each new Rad2Go product for thirty (30) days according to the following terms. This warranty extends to the original retail purchaser only and commences on the date of the original retail purchase. Any part of the Rad2Go Product manufacture or supplied by Rad2Go and found in the reasonable judgment of Rad2Go to be defective in material or workmanship will be repaired or replaced by an authorized Rad2Go service dealer without charge for parts and labor.
Rad2Go Electric Scooter Warranty This Warranty Registration is to be completed by the dealer or customer at the time of purchase and submitted to Rad2Go, Inc., within 10 days of the date of purchase for warranty entitlement. This warranty is void if the serial number or the safety warning labels on your Rad2Go Electric Scooter are altered, defaced, or removed. Modifications to your Rad2Go Electric Scooter or its components shall void this warranty.
3. This warranty does not apply to tire wear, operation under abnormal circumstances or contrary to the requirements described in the owner’s manual or damage to the vehicle brought on by improper use. Racing or competitive use shall void this warranty. 4. Warranty services may be obtained by contracting Rad2Go via telephone at (760) 929-1500, or by mail at 6231 Yarrow Drive, Suite C, Carlsbad, CA 92009; or via email at sales@rad2go.com.
_________ Never permit a guest to ride your Rad2Go Electric Scooter without reading the Owner’s Manual and all labels. _________ Rad2Go Electric Scooters should not be used by persons unwilling or unable to take responsibility for their actions. _________ Read all additional warnings and product instructions in the Owner’s Manual and on safety labels before operating the Rad2Go Electric Scooter.