RA13.2-16.2 Manual 12.03.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 2 TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Technical Design Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 3 INTRODUCTION Dear Customer, Congratulations on your purchase of a Radical Audio Inc. loudspeaker system. Your new component system is comprised of loudspeakers and crossovers, that have been precision engineered to produce the highest quality audio for your vehicle. This owner’s manual provides detailed information on the features, installation and adjustment of the Radical Audio “REFERENCE” component systems. The Radical Audio RA13.2RF and RA16.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 4 TECHNICAL DESIGN FEATURES MID/WOOFER RA13.2RF & RA16.2RF C 13 CM OR 16.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 5 INSTALLATION CONSIDERATIONS GENERAL SUGGESTIONS a Make sure you have enough high quality speaker wire at hand, to reach all the drivers and crossovers from their intended mounting locations! The preferable cross-section is 2 x 2.5mm2. Please note that for quality reasons, some of the speaker wiring must be purchased separately.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 6 MID/WOOFER INSTALLATION You can install the Radical Audio mid/woofers directly to the factory speaker mounting holes, because their Euro-DIN basket bolt hole configuration will fit to a great variety of European and Asian cars. a Remove the plastic grille (front door) and unscrew the factory installed 13cm or 16cm fullrange speaker unit. s Place the Radical Audio Inc.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 7 Fig.: Crossover Wiring AMP TWEETER INSTALLATION The tweeter units come with an aluminium main housing and a front rim that features three mounting holes. After you have determined the best sounding tweeter location, you can cut two holes with 50mm diameter, using a hole-saw attachment for your power drill. Before you mount the tweeters, you must solder a loudspeaker wire to the soldering terminals located on the backside of the tweeter.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 8 FINE TUNING OF TWEETER LEVEL ATTENTION: Before you start to fine tune tweeter level and presence level, be sure the following steps have been completed: z All wiring work has been done (loudspeakers, crossovers, amplifier are wired etc). z Highpass and lowpass crossover frequency adjustments have been set provisionally.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 9 FINE TUNING OF PRESENCE LEVEL a The presence level can be set by adjusting the jumper to “ ” or “ “ depending on the tweeter mounting location and personal preferences. s Slide back the transparent cover of the crossover unit and set the preferred attenuation level by adjusting the “presence” jumper on the circuit board. Note: Set the jumper to “ ”, if your tweeters are mounted relatively far away from the mid/woofers (like A-pillars or window triangle).
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 10 EINLEITUNG Wir gratulieren Ihnen zum Kauf dieses Radical Audio Inc. Lautsprechersystems. Ihr neues Komponentensystem, bestehend aus Einzellautsprechern und Frequenzweichen, wurde spezifisch für bestmögliche Klangwiedergabe im Fahrzeug entwickelt. Die Komponentenlautsprechersysteme von Radical Audio Inc., stehen synonym für den heutigen Stand der Technik, in Bezug auf Materialtechnologie, fortschrittliche Klebetechniken und hochpräzise Fertigungsmethoden.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 11 TECHNISCHE MERKMALE / FEATURES TIEFMITTELTÖNER RA13RF & RA16RF C 13 CM ODER 16.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 12 MONTAGEHINWEISE GENERELLES a Besorgen Sie sich vorab genügend Qualitativ hochwertiges Lautsprecherkabel mit einem Querschnitt von 2x2.5mm2.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 13 Einige Montage-Tipps: a Plazieren Sie die Hochtöner am besten dort, wo diese ohne direkte Hindernisse auf Fahrer und Beifahrersitze strahlen können, z.B. A-Säule oder Spiegeldreieck. s Nachdem Sie passende Montageorte gefunden haben, testen Sie beide Anschlussvarianten der Hochtonpolarität an der Frequenzweiche aus! Als erstes in Phase d.h. auf und auf genau wie an der Frequenzweiche angeschrieben.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 14 d Verwenden Sie die im Montagezubehör enthaltenen Stahlringe als Unterlage für die Montage der Tiefmitteltöner. Der Stahlring rückt den Korb des Tiefmitteltöners um 6mm nach vorne. Stellen Sie deshalb vor der Montage sicher, dass zwischen der Gummisicke des Tiefmitteltöners und der Originalabdeckung aus Plastik genügend Spielraum für die Membrane vorhanden ist. Die Sicke darf nicht anstossen und sollte ca.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 15 MONTAGE DER HOCHTÖNER Die dem Set beiliegenden 28mm Kalotten-Hochtöner RA28RF verfügen über ein Gehäuse mit einem Montagering aus Aluminium, der mit drei Befestigungslöchern versehen ist. Für die Montage muss nur ein Loch mit 50mm Durchmesser in die Fläche gebohrt werden, auf welcher der Hochtöner befestigt werden soll. Am einfachsten geht dies mit einem Kernbohraufsatz und einer elektrischen Bohrmaschine.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 16 Abb.: Jumperposition FEINEINSTELLUNG DES PRÄSENZBEREICHES a Der zweite Jumper mit der Bezeichnung „PRESENCE“ ermöglicht zwei unterschiedliche Pegelstufen im Präsenzbereich (2.2 bis 4kHz). Diese Abstufung ermöglicht eine Lautstärkeanpassung im unteren Hochtonbereich, je nach Montageort der Hochtöner, basierend auf dem Abstand zwischen Hochtöner und Tiefmitteltöner.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 17 TECHNICAL SPECIFICATIONS MID/WOOFER MODEL Nominal Diameter Nominal Impedance Voice Coil Diameter Frequency Response (- 3dB) Fs Vas Re Qes Qms Qts Mmd Xmax B/L Sensitivity Continuous Power Handling RA13.2RF 5 ¹⁄₄” (13 cm) Euro-DIN 4Ω 36 mm 60 Hz – 4 kHz 75 Hz 3.2 L 3.4 Ω 0.73 6.5 0.65 14.7 g 4.5 mm 5.7 T/m 84.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 18 RA13.2RF 73mm 119mm RA16.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 19 LIMITED WARRANTY Radical Audio Inc. warrants this component speaker system and it’s parts to be free of defects in materials and workmanship for TWO YEARS from the date of purchase at retail, contingent upon being properly installed and approved by an authorized Radical Audio Inc. dealer. Radical Audio Inc. will at its own discretion repair or replace any mechanically defective speaker unit or crossover during this warranty period.
RA13.2-16.2 Manual 12.03.2004 19:14 Uhr Seite 20 RADICAL AUDIO INC. 15584 E.