Radicom BPM730CE series Bluetooth HID Module Datasheet V1.7 Radicom Research, Inc. reserves the right to amend the document without notice at any time. Radicom assumes no responsibility for any errors appeared in the document, and disclaims any express or implied warranty, relating to sale and/or use of Radicom products including liability or warranties relating to fitness for a particular purpose, or Radicom Research, Inc. Copyright © 2014. All rights reserved www.radi.
Index 1. Introduction ..................................................................................................2 2. Features ........................................................................................................3 3. Product Specifications ................................................................................4 3.1 Function Block Diagram ...................................................................4 3.2 Applications Diagram 3.
1. Introduction Radicom BPM730CE series is a worldwide Bluetooth Human Interface Device (HID) module based on the latest Broadcom BCM20730 Bluetooth chip. It is integrated with PCB antenna, serial EEPROM, crystal, and also components for the built-in switching regulators to reduce the external BOM cost. Radicom BPM730CE series Bluetooth module integrates the entire profile, application, and Bluetooth protocol stack and is fully compliant with the Bluetooth SIG specification for human interface devices.
2. Features 1. Single-chip Bluetooth device with fully integrated Human Interface Device (HID) profile and full Bluetooth stack. 2. On-board ARM processor and RAM/ROM memory. 3. Custom-integrated Bluetooth core processor has been optimized to support the HID V1.0 profile and minimize power consumption. 4. Bluetooth version 3.0 compliant including support for enhanced power control (Unicast Connectionless Data) 5.
3. Product Specifications 3.1. Function Block Diagram 3.2. Applications Diagram 4 Radicom Research, Inc. Copyright © 2014. All rights reserved www.radi.
3.3. Bluetooth related Specification Wireless Bluetooth v3.0 Class 2 (Broadcom20730chip) Data Rate Bluetooth v3.0 (1Mbps) Bandwidth 2.402GHz – 2.
3.5 Mechanical Dimension Top side view: Board size = 30.556 mm x 14.986 mm Pitch of short side = 1.27 mm Pitch of long side = 1.143 mm Pad width = 0.914 mm Module Height Maximum height = 3.0 mm Board thickness = 0.80 mm 6 Radicom Research, Inc. Copyright © 2014. All rights reserved www.radi.
3.
3.7 Pin Definition Pin No.
31 P4 I/O Port 4 32 P7 I/O Port 7 33 P6 I/O Port 6 34 UART_TX O Debug UART transmit port 35 UART_RX I Debug UART receiver port. After power on reset, if UP_RX =1, firmware download mode UP_RX=0, normal mode 36 P2 I/O Port 2 37 P21 I/O Port 21 38 RESET_N I Active low system reset with a weak pull up.
4. FCC & IC Label and Model Identification The BPM730CE module family is FCC Part 15 and IC (Industry Canada) certified. The BPM730CE is also CE marked. The modules are labeled with the BPM730CE module model number and FCC Part 15 ID, IC registration number and CE mark. The label can be found on top of the metal shielding on the BPM730CE Module. Radicom Research Inc. Radicom Research Inc.
5. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
IMPORTANT NOTE: FCC Radiation Exposure Statement: The product comply with the US portable RF exposure limit set forth for an uncontrolled environment and are safe for intended operation as described in this manual. The further RF exposure reduction can be achieved if the product can be kept as far as possible from the user body or set the device to lower output power if such function is available. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
End Product Labeling The final end product must be labeled in a visible area with the following: “Contains FCC ID: K7T- BPM730CE Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 13 Radicom Research, Inc. Copyright © 2014.
6. Industry Canada statement: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: 1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.
15 End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC: 2377A- BPM730CE Plaque signalétique du produit final Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: Contient des IC: 2377A- BPM730CE Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates th
7. CE Declaration of Conformity For the following equipment: Radicom Research Inc. Wi-Fi Module Mode(s): BPM730CE, RB730 are herewith confirmed to comply with the requirements set out in the Council (European parliament) Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility of Radio and Telecom device (1999/5/CE). For the evaluation regarding this Directive, the following standards were applied: EN 300328 V1.8.1: 2012 EN 62311:2008(MPE) EN 301489-1 V1.9.
