OWNER’S MANUAL PLCD32 PLL SYNTHESIZER STEREO RADIO WITH COMPACT DISC PLAYER DIGITAL
INSTALLATION Notes: • Choose the mounting location where the unit will not interfere with the normal driving function of the driver. • Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly. • Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.
1. Dashboard 1 2. Nut (5mm) 6 3. Spring washer 7 4 2 4. Screw (5 x 25mm) 5 5. Screw 3 6. Strap Be sure to use the strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. (Fig. 2) 7. Plain washer Removing the unit 1. Frame 1 2. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When reattaching the frame, point the side with a groove downwards and attach it.) 2 3 3.
HOW TO REMOVE AND INSTALL THE FRONT PANEL 1. Press the release button and pull-off the front panel. Keep front panel into the case. 2. To install the front panel, insert the panel into the housing and make sure the panel is properly installed, otherwise, abnormalities occurs on the display or some keys will not function properly.
WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR IGNITION RED SWITCH (B+) (GREY) RCA CABLE MEMORY YELLOW BACK-UP BLACK GROUND (B–) POWER ANTENNA 2-SPEAKERS SYSTEM WHITE Rch RED Lch WHITE BLUE 4-SPEAKERS SYSTEM FRONT Lch SPK. 4-SPEAKERS SYSTEM WHITE GREY WHITE/BLACK GREY/BLACK 2-SPEAKERS SYSTEM GREY FRONT Rch SPK. Lch SPK. Rch SPK. GREEN/BLACK REAR Lch SPK. GREEN VIOLET GREEN/BLACK VIOLET/BLACK REAR Rch SPK. VIOLET/BLACK Note: 1.
OPERATION 7 17 2 1 16 18 13 20 3 21 5 8 22 14 23 12 10 11 4 19 15 6 9 24 25 GENERAL OPERATION • ON/OFF Switch on the unit by pressing any button [except button (4) and RELEASE button (7)]. When system is on, press button (9) to turn off the unit. • FACEPLATE RELEASE Press RELEASE button (7) to detach the removable faceplate.
• SOUND ADJUSTMENT Press SEL button (10) to select the desired adjustment mode. The adjustment mode will change in the following order: Volume Bass Treble By pressing VOL button (11) or VOL desired sound quality. Balance Fader button (12), it is possible to adjust the • LOUDNESS Press BND/LOU button (13) for several seconds to reinforce the bass output and display will show “LOUD”. Press it for several seconds again to release this function.
RADIO OPERATION • BAND SELECTION At tuner mode, press BND/LOU button (13) shortly to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM • STATION SELECTION Press TUNE/SEEK/TRACK button (16) or TUNE/SEEK/TRACK button (17) shortly to activate automatic seek function. Press for several seconds until “MANUAL” appeared on the display, the manual tuning mode is selected.
CD OPERATION • SELECT TRACKS Press TUNE/SEEK/TRACK button (16) or TUNE/SEEK/TRACK button (17) to move to the previous track or the following track. Track number shows on display. Hold TUNE/SEEK/TRACK button (16) or TUNE/SEEK/TRACK button (17) to fast reverse or fast forward. CD play starts from when you release the button. • PAUSE PLAYING Press PAU button (20) to pause CD player. Press it again to resume play. • REPEAT THE SAME TRACK Press RPT button (22) to continuously repeat the same track.
SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls - Bass (at 100 Hz) - Treble (at 10 KHz) Maximum Output Power Current Drain : DC 12 Volts, Negative Ground : 178 (W) x 165 (D) x 50 (H) : : : : + 10 dB / – 10 dB + 10 dB / – 10 dB 40W x 4 (ch) 5 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 60 dB : More than 60 dB : 20 Hz - 20 KHz RADIO FM 87.5 to 107.9 MHz 10.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cause Solution The car ignition switch is not on. If the power supply is properly connected to the car accessory circuits, but the engine is not moving, switch the ignition key to “ACC”. The fuse is blown. Replace the fuse. Presence of CD disc inside the player.
www.pyleaudio.
