PLCDCS 200 OWNER’S MANUAL Mobile Audio System • PLL Synthesizer Stereo Radio • Digital Compact Disc Player • Cassette Player • Automatically Memory Storing • Preset Equalization • Auxiliary Input Function • Remote Control • Undetachable Panel
CONTENTS Installation .....................................................................................................3 Wiring Connection ........................................................................................4 4 x 50W System......................................................................................................4 Operation .......................................................................................................5 General Operation ...........................
INSTALLATION Method A SUB PANEL FLANGE NUT QUICKIE BOLT REAR BUSHING FACTORY BRACKET MOUNTING SCREW QUICKIE BOLT DASH PANEL Method B SUB PANEL QUICKIE BOLT FLANGE NUT MOUNTING SCREW 2#BRACKET DASH PANEL MOUNTING SCREW 2#BRACKET 2#BRACKET 3#BRACKET 1#BRACKET STANDARD MOUNTING CONFIGURATION 2#BRACKET 2#BRACKET “JA” MOUNTING CONFIGURATION 3 “JZ” MOUNTING CONFIGURATION
WIRING CONNECTION For 4 x 50W System MAIN UNIT ANTENNA SOCKET IGNITION SWITCH (B+) RED FUSE (BLACK) Rch RED TV AUDIO IN MEMORY BACK-UP GROUND (B–) YELLOW Lch WHITE (GREY) BLACK RCA CABLE Rch RED Lch WHITE POWER ANTENNA FRONT Lch SPEAKER REAR Lch SPEAKER BLUE WHITE GREY WHITE/BLACK GREY/BLACK GREEN VIOLET GREEN/BLACK VIOLET/BLACK 4 FRONT Rch SPEAKER REAR Rch SPEAKER
OPERATION 12 16 9 13 10 17 19 4 28 27 20 8 3 15 7 21 18 22 23 11 14 5 24 26 5 1 25 6 2
OPERATION • SELECT MODE Press the MODE button (6) to choose desired listening mode. (e.g. radio, CDP, CDC, tape, TV or AUX mode) GENERAL OPERATION Note: In this product design, there has different sound accompanying with every button pressed and the sound is designed differently according to the customers. • MUTE Press the MUTE button (2) to silence the receiver. Press it again to release the mode. • ON/OFF Switch on the unit by pressing POWER button (9).
OPERATION memorized, the seconds Auto Store search continued by Distant state. At the end of Auto Store operation, mode is change to Preset Scan. RADIO OPERATION • BAND SELECTION At radio mode, press BAND button (13) to select the desired band. The reception band will change in the following order: FM1 FM2 FM3 AM1 - Preset Scan Press AS/PS button (14) shortly in radio mode, Preset Scan is started.
OPERATION CDP OPERATION REMOTE CONTROL HANDSET • SELECT TRACKS Press TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to move to the previous track or the following track. Track number shows on display. Hold TUNE/TRACK/SKIP button (16) or TUNE/TRACK/SKIP button (17) to fast reverse or fast forward. CD play starts from when you release the button. 1 7 4 3 8 9 6 5 13 2 12 10 11 14 15 • PAUSE PLAYING Press PAU button (19) to pause CD player. Press it again to resume play.
SPECIFICATIONS GENERAL Power Supply Requirements Chassis Dimensions Loading Impedance Maximum Output Power Current Drain : : : : : DC 12 Volts, Negative Ground 200 mm (W) x 138 mm (D) x 75 mm (H) 4 - 8 Ω per channel 4 x 50 Watts 10 Ampere (max.) CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response : More than 55 dB : More than 50 dB : 20 Hz - 20 KHz CASSETTE PLAYER Tape Speed Fast Forward Time Frequency Response Channel Separation Crosstalk Wow and Flutter : : : : : : 4.
TROUBLE SHOOTING Before going through the check list, check wiring connection. If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power. Disc cannot be loaded or ejected. Cassette tape cannot be loaded or ejected. No sound. Sound skips or sound quality is poor. The operation keys do not work. Cause Solution The car ignition switch is not on.
MAINTENANCE 3. Clean the tape head with the cotton swab. For System The following suggestions help you care for the product so that you can enjoy it for years. 1. Keep the product dry. If it does get wet, wipe it dry immediately. Liquids might contain minerals that can corrode the electronic circuits. 4. Clean the capstans and the pinch rollers with the cotton swab. 2. Keep the product away from dust and dirt, which can cause premature wear of parts. 5.
CAUTION 1. This unit is designed to operate on 12-volts DC, negative ground electrical system only. Do not attempt to install this unit in a vehicle having a positive ground system. 2. You should not touch the high-polished playback head with any metallic or magnetic tools. 3. Your unit has built-in filtering to eliminate most of the noise that might come through the power source. However, with some vehicles, particularly older models, some clicking or other unwanted noise might be present.
