RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 1
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 2 8-IN-ONE REMOTE POWERED BY KAMELEON TABLE OF CONTENTS Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 How Kameleon™ Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Installing Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 3 OWNER’S MANUAL Instruction To The User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Limited 90-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 Manual De Deuño . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 Manufacturer’s Codes . . . . . . . . . . . .
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 4 8-IN-ONE REMOTE POWERED BY KAMELEON HOW KAMELEON™ WORKS (Continued) Several devices have a second menu that can be accessed using SCREEN (see Device Menu Screens, starting on page 45). For example, TV has two menus: a main menu with extra feature keys for COM MUTE, +100, ENTER, SLEEP, TV/VCR, and PIP functions, and a second menu screen that adds navigation keys but removes the extra feature keys.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 5 OWNER’S MANUAL ❶ ❸ ❷ 1. Push forward on the battery compartment cover (on the back of the remote) and lift it off. 2. Slide the AAA batteries into the compartment as indicated by the polarity symbols (+ and –) shown above. 3. Align the cover with the compartment opening and slide it back into place. 4. If batteries are inserted correctly, the display will turn on and show all keys. If a key is not pressed after 7 seconds, the display will turn off.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 6 8-IN-ONE REMOTE POWERED BY KAMELEON INSTALLING BATTERIES ABOUT THE FINDER TRANSMITTER (CONTINUED) INSTALLING A BATTERY IN THE FINDER TRANSMITTER ❶ ❷ ❸ 1. Press down on the battery compartment cover (on the front of the Finder Transmitter) and slide it off. 2. Locate the snap harness and connect the 9-volt battery to mating terminals. Then insert the battery and harness into the compartment. 3.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 7 OWNER’S MANUAL To find out what keys appear when the program mode is activated or when a device is selected, see the Device Menu Screens section starting on page 45. Included are brief descriptions of how the keys work for each displayed screen. continued on next page...
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 8 8-IN-ONE REMOTE POWERED BY KAMELEON A QUICK LOOK AT THE CONTROLS (Continued) KEY FUNCTIONS When a key is pressed, the IR segments will animate. Outgoing animation (see arrow) indicates the remote is sending IR signals to a selected device. Incoming animation indicates the remote is receiving IR signals from a device being learned (see Using Learning on page 19). During programming, the bottom IR segment flashes to confirm setup actions.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 9 OWNER’S MANUAL In the CD mode, use ▲ (or ▼) to select the next (or previous) disc. ▲ ▲ In the AUD mode, use ▲ (or ▼) to raise (or lower) rear channel volume and use (or ) to balance audio left (or right). Use OK to choose options from your device’s menu or guide. Press LAST once to recall the last channel. In the CD or AUD mode, use LAST to repeat the last track.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 10 8-IN-ONE REMOTE POWERED BY KAMELEON A QUICK LOOK AT THE CONTROLS KEY FUNCTIONS (CONTINUED) In all modes except AUD, use the number keys (1 ~ 9 and 0) to directly select channels (e.g., 009 or 031) or enter numbers. In the AUD mode, INPUT will appear. Use the number keys to directly select inputs 1 ~ 9 and 10. For certain brands in all modes except CD, press ENTER once after entering numbers (if required on original remote control).
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 11 OWNER’S MANUAL ▲ Use MODE to reassign an unused device key to control a second device. See Reassigning Device Keys on page 35. NOTE: Press above the title to activate a desired program. For OTHER, press below the title. Use OTHER to program other functions.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 12 8-IN-ONE REMOTE POWERED BY KAMELEON A QUICK LOOK AT THE CONTROLS KEY FUNCTIONS (CONTINUED) In the CBL, SAT, VCR, DVD, or AUX mode, use the slow key to view slow motion video (if the feature is available). Use PIP to switch the Picture-In-Picture feature on or off. Use MOVE to move the window picture to different places in the main picture. Press FRZ once to capture a frame of video in the main picture. Press it again to resume normal viewing.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 13 OWNER’S MANUAL ADJUSTING BRIGHTNESS The RadioShack 8-in-One Remote has five levels of brightness adjustment and is set to the fourth one at the factory. To increase or decrease the brightness, perform the following steps: 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: NOTE: If the display turns off because of inactivity, you will need to start the programming sequence again by repeating this step. 2.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 14 8-IN-ONE REMOTE POWERED BY KAMELEON PROGRAMMING A DEVICE The RadioShack 8-in-One Remote is preset at the factory to operate the following devices: • Motorola Cable Box • RCA TV, VCR, DVD Player, Satellite Receiver, CD Player, and Audio Receiver • ReplayTV PVR (DVR) using the AUX key To control devices other than the default brands, perform the following steps; otherwise skip this section: NOTE: To control a DVD Player/VCR Combo, perform the instructi
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 15 OWNER’S MANUAL 4. Press a device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD). The selected device key will animate. NOTE: Refer to the “Device Table” on page 12 when choosing a device key for programming. 5. Use the Manufacturer’s Codes (starting on page 118) to locate the type of device and brand name and then use the number keys to enter the first four-digit code for your device.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 16 8-IN-ONE REMOTE POWERED BY KAMELEON PROGRAMMING A DVD PLAYER/VCR COMBO NOTE: If you own a Sylvania TV/DVD Player Combo with a separate TV code (see page 129), use the below steps to program it with these changes: in step 5 (on the next page), enter 0675 as the DVD code; in step 8a, substitute TV for VCR; and in step 8b enter 0171 as the TV code. 1. Turn on the DVD Player/VCR Combo and insert a DVD.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 17 OWNER’S MANUAL a. Press VCR once. b. Using the number keys, enter the four-digit VCR code for your DVD Player/VCR Combo. If performed correctly, the bottom IR segment will flash twice. c. Press OK once. The bottom IR segment displays one long flash. NOTE: If a VCR setup code is not listed, you can use the VCR key to program a separate VCR or another device (see “Reassigning Device Keys” on page 35). 8. To exit programming, press twice.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 18 8-IN-ONE REMOTE POWERED BY KAMELEON SEARCHING FOR YOUR CODE (Continued) 3. Press a device key once (e.g., TV). The selected device key will animate. The device’s Main Menu screen will appear with still displayed. 4. Press PWR once to select it as the search test function. The Search Programming screen will appear again. NOTE: With PWR as the search test function, a “Power On” IR command will be sent to the device each time a test code is sent.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 19 OWNER’S MANUAL 3. Using the number keys, enter 9 9 0. The bottom IR segment will flash twice and the Code Verification screen will appear. 4. Press a desired device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD). The selected device key will animate. 5. To view the code for the first digit, press 1 once. Count the number of times the bottom IR segment flashes (e.g.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 20 8-IN-ONE REMOTE POWERED BY KAMELEON USING LEARNING LEARNING PRECAUTIONS (CONTINUED) • Learned keys can be used in macros (see Using Macros on page 25). • Do not use the following keys for learning: P, SCREEN, M1~ M4, FAV SCAN, COM SKIP, COM MUTE, or any device key. • Learning capacity is approximately 16 to 25 keys, depending on the code being learned.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 21 OWNER’S MANUAL 2" 5. On the RadioShack 8-in-One Remote, select and press a desired key where the learned function will be stored. The IR segments will display an incoming animation, continue for three revolutions, and then the entire display will turn off. After the display is off, press and hold the teaching key (on your original remote control) until the display (on the RadioShack 8-in-One Remote) turns on again.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 22 8-IN-ONE REMOTE POWERED BY KAMELEON USING LEARNING DELETING A SINGLE LEARNED KEY (CONTINUED) 5. If desired, repeat steps 2 through 4 to delete another learned key. 6. Exit programming by pressing once. The display will return to the last-selected device menu screen. DELETING ALL LEARNED KEYS IN A SPECIFIC MODE 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Press above IR DELETE once.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 23 OWNER’S MANUAL LOCKING VOLUME CONTROL TO ONE MODE (GLOBAL VOLUME LOCK) 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Press above VOL once. The Volume Lock programming screen will appear: 3. Press a device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD) where you want the volume controls locked to. The bottom IR segment will flash twice and the program keys will appear again. 4.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 24 8-IN-ONE REMOTE POWERED BY KAMELEON CHANGING VOLUME LOCK UNLOCKING VOLUME CONTROL FOR A SINGLE DEVICE (INDIVIDUAL VOLUME UNLOCK), CONTINUED 3. Press VOL▼ once. Then press a device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD) where you want the volume controls unlocked. The bottom IR segment will flash four times and the program keys will appear again. 4.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 25 OWNER’S MANUAL USING MACROS The RadioShack 8-in-One Remote includes six macro keys: M1 through M4, COM MUTE, and PWR. Each one can be set up to perform a repetitive, time-consuming operation with the press of a single key. NOTES: A macro programmed onto the PWR key can only be accessed in the MY SYSTEM mode. Pressing it in any other mode will only send a “Power On/Off ” IR command to the selected device.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 26 8-IN-ONE REMOTE POWERED BY KAMELEON USING MACROS PROGRAMMING A FAVORITE CHANNEL MACRO (CONTINUED) NOTE: If there are more than 15 key presses in the sequence, the bottom IR segment will display a long flash, denoting an error. The display will return to the last-selected device menu screen. To program the macro, start again with step 3. 5. To save the macro, press and hold P until the bottom IR segment flashes twice. The program keys will appear again. 6.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 27 OWNER’S MANUAL 6. Exit programming by pressing once. The display will return to the last-selected device menu screen. 7. To test the power macro, first make sure all home theater devices selected in step 4 are turned on.Aim the remote control at the devices and press MY SYSTEM once, followed by PWR once. The devices should turn off in this order: Satellite Receiver, DVD Player, Audio Receiver, and TV.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 28 8-IN-ONE REMOTE POWERED BY KAMELEON USING MACROS (Continued) CLEARING A MACRO 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Press above MACRO once. The Macro programming screen will appear: 3. Select the macro key to be cleared and press it once. The last-selected device menu screen will be displayed. 4. Press and hold P until the bottom IR segment flashes twice. The program keys will appear again. 5.
RS 8in1 Kameleon OM rev 10/9/03 4:11 PM Page 29 OWNER’S MANUAL 2. Press below OTHER once. The Other programming screen will appear: 3. Using the number keys, enter 9 9 4. The bottom IR segment will flash twice. 4. For the source mode, press a desired device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD). For this example, press TV once. The selected source device menu screen, including , will be displayed. 5. For the source key, press a key to be moved once. For this example press VOL ▲ once.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 30 8-IN-ONE REMOTE POWERED BY KAMELEON USING KEYMOVER RESTORING A SINGLE KEYMOVED KEY (CONTINUED) 2. Press below OTHER once. The Other programming screen will appear: 3. Using the number keys, enter 9 9 4. The bottom IR segment will flash twice. 4. Press the destination mode once where the keymoved key is stored. Then press the destination key twice. Upon key restoration, the bottom IR segment will flash twice as confirmation.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 31 OWNER’S MANUAL 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Select a Favorite Channel Mode by pressing CBL, SAT, TV, VCR, or AUX once. The bottom IR segment flashes once as the selected device key animates. 3. Press below OTHER once. The Other programming screen will appear: 4. Using the number keys, enter 9 9 6.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 32 8-IN-ONE REMOTE POWERED BY KAMELEON USING CHANNEL SCAN In the CBL, SAT, TV, VCR, or AUX mode, use FAV SCAN to start a 3-second scan of all favorite channels (if programmed – see Programming Favorite Channel Scan on page 30) and/or all channels for the selected mode. 1. If Favorite Channel Scan has been set up, skip to step 2. Otherwise, press CBL, SAT, TV, VCR, or AUX once. The bottom IR segment flashes once as the selected device key animates. 2.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 33 OWNER’S MANUAL Channel Controls Group: CBL, SAT, TV, DVD, VCR, and AUX Menu Controls Group: CBL, SAT, TV, DVD, AUD, VCR, AUX, and CD FACTORY DEFAULT SETTINGS At the factory, the Control Groups are assigned the following modes as default settings: Video Playback Group: DVD Volume Controls Group: AUD Channel Controls Group: CBL Menu Controls Group: CBL If the default settings fit your needs, you can skip programming this mode.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 34 8-IN-ONE REMOTE POWERED BY KAMELEON USING MY SYSTEM MODE PROGRAMMING MY SYSTEM MODE (CONTINUED) 4. To assign a mode to the Video Playback group, press a device key once (i.e., CBL, SAT, TV, DVD, AUD, VCR, AUX, or CD). Then the Volume Controls programming screen will appear: 5. To assign a mode to the Volume Controls group, press a device key once. Then the Channel Controls programming screen will appear: 6.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 35 OWNER’S MANUAL REASSIGNING DEVICE KEYS The RadioShack 8-in-One Remote can be set to control a second device. For example, to control a TV, a Cable Box, and two DVD Players, you can reassign the unused AUX key to operate the second DVD Player as follows: 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: ▲ 2. Press above MODE once.The Mode Mover programming screen will appear: 3.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 36 8-IN-ONE REMOTE POWERED BY KAMELEON USING COMMERCIAL SKIP The RadioShack 8-in-One Remote includes a unique feature for skipping past commercials on recorded programs when using a PVR (DVR) or VCR. This features works in the CBL, SAT, VCR, or AUX mode and you can use the default settings or program custom ones..
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 37 OWNER’S MANUAL 5. Using the number keys, enter 9 7 4. The The bottom IR segment will flash twice and the Commercial Skip programming screen will appear: 6. Select a Commercial Skip mode by pressing CBL, SAT, VCR, or AUX once. 7. Press FFWD once and watch for the end of a commercial sequence that typically may have four to six commercials and last 2 to 3 minutes in real time.As it ends, press PLAY once.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 38 8-IN-ONE REMOTE POWERED BY KAMELEON SETTING THE TILT SWITCH The RadioShack 8-in-One Remote contains a Tilt Switch that activates the display when the unit is moved. If desired, you can disable it so only pressing a key will turn on the display. NOTE: Disabling the Tilt Switch can help conserve battery life. DISABLING THE TILT SWITCH 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Press below OTHER once.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 39 OWNER’S MANUAL SETTING THE FINDER RECEIVER The RadioShack 8-in-One Remote comes with a Finder Transmitter that can be used to quickly locate the main remote if it is accidentally lost or misplaced. At the factory, the Finder Receiver (inside the remote) is set to wake up every few seconds, listen for a signal from the Finder Transmitter, and then emit an audible alert to pinpoint the location of the main remote.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 40 8-IN-ONE REMOTE POWERED BY KAMELEON RESTORING FACTORY DEFAULT SETTINGS The RadioShack 8-in-One Remote includes a Setup Code Reset program. You can use it to restore all your programmed codes to factory settings and delete all custom programming.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 41 OWNER’S MANUAL 1. Press and hold P until the bottom IR segment flashes twice. The program keys will appear: 2. Press below OTHER once. The Other programming screen will appear: 3. Using the number keys, enter 9 8 0. The bottom IR segment will flash twice, pause and flash twice again to confirm restoration. 4. Exit programming by pressing once. The display will return to the last-selected device menu screen. SPECIFICATIONS Remote Power . . . . . . . . .
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 42 8-IN-ONE REMOTE POWERED BY KAMELEON ABOUT UPGRADING Your RadioShack 8-in-One Remote has the largest infrared code library available and contains a unique feature that allows new codes to be added to its memory over the phone. In a matter of seconds, your remote will quickly and reliably record the new information without complex plugs, adapters, or attachments.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 43 OWNER’S MANUAL • Broken or defective product. • Products that operate over 100 kHz. • Infrared keyboards a nd infrared pointing devices (such as mouse substitutes). • All products for sale and/or use outside the continental United States, Hawaii, Alaska, or Canada. TROUBLESHOOTING PROBLEM: No display at all times. SOLUTION: Replace batteries with four new AAA alkaline batteries. PROBLEM: No display when programming.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 44 8-IN-ONE REMOTE POWERED BY KAMELEON TROUBLESHOOTING (Continued) PROBLEM: Power macro does not work. SOLUTION: First press MY SYSTEM once, then press PWR once. PROBLEM: Favorite channel function does not work properly. SOLUTION: Some devices (e.g.,Cable Boxes or Satellite Receivers) use two-digit channel numbers.During programming, press ENTER or OK once after entering a channel number (e.g., 0 2 ENTER for channel 2).
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 45 OWNER’S MANUAL DEVICE MENU SCREENS PROGRAMMING MAIN MENU ▲ Pressing and holding P displays the Programming Main Menu screen. Use the program keys to program device control (DEV SET), code search (SEARCH), home theater mode (MY SYSTEM), volume lock (VOL ), macros (MACRO), display brightness ( ), function learning (IR LEARN and IR DELETE), device key reassignment (MODE ), or other functions (OTHER).
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 46 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) AUD MAIN MENU Pressing AUD once displays the AUD Main Menu screen. After device programming, use these keys to remotely control your Audio Receiver’s or Amplifier’s volume and stations, select source inputs, operate transport functions on a built-in CD player (or DVD player, if HTiB device), and access menu or preset functions.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 47 OWNER’S MANUAL AUD MENU Pressing SCREEN once (on the AUD Main Menu, as shown on the previous page) displays a secondary AUD Menu screen. Use these keys to remotely control your Audio Receiver’s or Amplifier’s volume, stations, and surround functions. Pressing SCREEN once more returns the display to the AUD Main Menu screen.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 48 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) AUX MAIN MENU Pressing AUX once displays the AUX Main Menu screen. After device programming, use these keys to remotely control all your device’s common features, such as volume and channels, and menu, guide, and navigation functions.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 49 OWNER’S MANUAL CBL MAIN MENU Pressing CBL once displays the CBL Main Menu screen. After Cable Box programming, use these keys to remotely control all your device’s common features, such as volume and channels, and menu, guide, and navigation functions.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 50 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) CD MAIN MENU Pressing CD once displays the CD Main Menu screen. After device programming, use these keys to remotely control your CD player’s common features, such as transport keys and skip, menu, and random functions. Pressing SCREEN once will display a secondary CD Menu (as shown on the next page).
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 51 OWNER’S MANUAL CD MENU Pressing SCREEN once (on the CD Main Menu, as shown on the previous page) displays a secondary CD Menu screen. Use these keys to remotely control your CD player’s navigation functions. Pressing SCREEN once more returns the display to the CD Main Menu screen.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 52 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) DVD MAIN MENU Pressing DVD once displays the DVD Main Menu screen. After device programming, use these keys to remotely control all your DVD player’s common features, such as transport keys and menu, navigation, subtitle, and audio functions.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 53 OWNER’S MANUAL MY SYSTEM MAIN MENU After mode programming, pressing MY SYSTEM once displays the My System Main Menu screen. Use these keys to remotely access all common features and functions of your home theater system. For details, see Using My System Mode on page 32.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 54 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) TV MAIN MENU Pressing TV once displays the TV Main Menu screen. After device programming, use these keys to remotely control all your TV’s common features, such as volume and channels, and last channel, menu, and information/display functions. Pressing SCREEN once will display a secondary TV Menu (as shown on the next page).
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 55 OWNER’S MANUAL TV MENU Pressing SCREEN once (on the TV Main Menu, as shown on previous page) displays a secondary TV Menu screen. Use these keys to remotely control all your TV’s common menu features. Pressing SCREEN once more returns the display to the TV Main Menu screen.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 56 8-IN-ONE REMOTE POWERED BY KAMELEON DEVICE MENU SCREENS (Continued) VCR MAIN MENU Pressing VCR once displays the VCR Main Menu screen. After device programming, use these keys to remotely control all your TV’s common features, such as volume and channels, and last channel, menu, and information/display functions, and VCR transport controls.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 57 OWNER’S MANUAL CARE • Keep the remote dry. If the remote gets wet, wipe it dry immediately. • Handle the remote gently and carefully. Don’t drop it. • Use and store the remote only in normal temperature environments. • Keep the remote away from dust and dirt. • Wipe the remote with a damp cloth to keep it looking new. Modifying or tampering with internal parts can cause damage and invalidate the warranty.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 58 8-IN-ONE REMOTE POWERED BY KAMELEON INSTRUCTION TO THE USER This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
RS 8in1 Kameleon OM rev 10/9/03 4:12 PM Page 59 OWNER’S MANUAL RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you.