Operating Guide Guide d’emploi Guia para el uso Please read this entire guide before installing. Veuillez lire tout ce manuel avant de commencer. Por favor, lea completamente esta guía antes de comenzar.
Important Safety Information Explanation of Attention Words and Symbols used in this guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. WARNING WARNING indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Thank you for choosing the PetSafe® brand. You and your pet deserve a companionship that includes memorable moments and a shared understanding together. Our products and training tools promote a lifestyle of protection, teaching, and love—essentials that influence memories for a lifetime. If you have any questions about our products or training your pet, please visit our website at www.petsafe.net or contact our Customer Care Center.
Components Located inside the battery compartment is the SmartKey™, RFA-67 battery, mounting screws and key ring. SmartKey™ Operating Guide Battery (PetSafe® RFA-67) Interior Frame with Flap Mounting Screws (4 pcs. small door) (8 pcs.
SmartDoor™ – The SmartDoor™ is an intelligent receiver using an internal antenna to pick up a unique SmartKey™ code for selective pet entry and exit. SmartDoor™ Flap – The SmartDoor™ flap is a weather resistant, plastic flap with UV sun protection. Antenna - The antenna is located inside the SmartDoor™ and receives radio signals from the SmartKey™. The SmartKey™ must be located within a certain proximity of the antenna in order for the unique code to be read.
A. Place Batteries in the SmartDoor™ 1. With a Phillips screwdriver, remove the two Battery Compartment Cover screws. 2. Remove the Battery Compartment Cover. 3. Refer to the inside of the Battery Compartment Cover for the proper orientation of the four D-Cell (LR20) batteries. 4. Replace the Battery Compartment Cover and reinstall the two screws. 5.
AUTOMATIC MODE – Allows entry and exit for a pet wearing a programmed SmartKey™. To set: hold the MODE-RESET button until the yellow light illuminates and release when selected. Five SmartKeys™ can be programmed to one SmartDoor™ for selective entry and exit during AUTOMATIC MODE. NOTE: If at any time the red light remains illuminated, replace with a set of fresh batteries. If that does not reset the red light, please call our Customer Care Center for additional help.
Step Preparing Door 2 2A 2A Remove door from hinges. 2B Place on a raised level surface such as saw horses. Helpful Tip: Clamp or weigh down the door to prevent it from moving. 2B 2C NOTE: The pet door can be installed with the door hanging based on your skill level. 2C Match the marked lines on the door with the shoulder and center lines on the template. Tape the template in place. NOTICE When applying the template there should be a minimum of 3” (7.
Step Install Pet Door 4 Before putting away the jigsaw, place the interior frame (frame with the flap) inside the cut out and check the fit. Then, place the exterior frame into the underside of the door to check the fit. If frames do not fit inside the opening, you may need to recut to square opening before proceeding with installation. 4 4 Re-hang door and place interior frame with flap inside cut-out of interior door.
NOTE: The SmartDoor™ is designed with an electric motor to release and unlock flap when a SmartKey™ is detected. Do not allow your pet to run or charge through the SmartDoor™. Due to variable radio-frequency interferences it could take several seconds for SmartKey™’s unique code to read properly and SmartDoor™’s flap to unlock. SET A.
C. Programming a New SmartKey™ To reduce error while programming, remove the RFA-67 battery from all programmed SmartKeys™ except the one you are programming. Press and hold the LEARN button until the green light illuminates and begins to flash, now release the button. Bring the SmartKey™ directly below the green light and the light will stop flashing and illuminate for two seconds. Now your new SmartKey™ has been programmed and added to memory. Up to five different SmartKeys™ can be added, one at a time.
Yellow light is flashing Red light remains illuminated (internal failure has occurred) Red light is flashing Red, green and yellow lights are flashing • Obstruction to the flap has been detected. • Press the MODE-RESET button to cause the SmartDoor™ to attempt to lock the flap. Clear any obstructions that keep the flap from locking. When the flap successfully locks, normal operation is resumed.
This product has the benefit of a limited manufacturer’s warranty. Details of the warranty applicable to this product and its terms can be found at www.petsafe.net and/or are available by sending a stamped addressed envelope to PetSafe® Ltd. Redthorn House, Unit 9, Chorley West Business Park, Ackhurst Road, Chorley, Lancashire PR7 1NL, United Kingdom. ______________________________________________________________________________ Terms of Use and Limitation of Liability 1.
instruction guide, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a practical installation. If this equipment causes harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Relocate the interfered receiving antenna.