Data Sheet

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’ s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
‐Reorient or relocate the receivingantenna.
‐Increase the separation between the equipment andreceiver.
‐Connect the equipment into an outlet on a circuit different from that towhich the receiver is connected.
‐Consult the dealer or an experienced radio/TV technician for help important announcement
Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm between the radiator and your
body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Country Code selection feature to be disabled for products marketed to the US/Canada.
This device is intended only for OEM integrators under the following conditions:
1.The antenna must be installed such that 20 cm is maintained between the antenna and users,and
2.The transmitter module may not be co-located with any other transmitter orantenna,
3.For all products market in US, OEM has to limit the operation channels in CH1 to CH78 for 433M band
by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user
regarding to Regulatory Domain change. (if modular only test Channel1-78)
As long as the three conditions above are met, further transmitter testing will not be required. However, the OEM integrator
is still responsible for testing their end-product for any additional compliance requirements required with this module
installed.
Important Note:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another
transmitter), then the FCC authorizationis no longer considered valid and the FCC ID cannot be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter)
and obtaining a separate FCC authorization.
EndProduct Labeling
The final end product must be labeled in a visible area with the following" Contains FCC ID: 2ANH5-RC-CC1101-434"
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF
module in the user’s manual of the end product which integrates this module.
The end user manual shall include all required regulatory information/warning as show in this manual.
Integration instructions for hostproduct manufacturers according to KDB 996369 D03 OEM Manual v01
2.2 List of applicable FCCrules
CFR 47 FCC PART 15 SUBPART C has been investigated. It is applicable to the modular transmitter
2.3 Specific operational useconditions
This module is stand-alonemodular. If the end product will involve the Multiple simultaneously transmitting condition or
different operational conditions for a stand-alone modular transmitter in a host, host manufacturer have to consult with
module manufacturer for the installation method in end system.
2.4 Limited moduleprocedures
This module is Limited modular without shielding, host manufacturer have to consult with module manufacturer for the
module
limiting conditions when integrate the module in the host. module manufacturer should reviews detailed test data or host
designs prior to giving the host manufacturer approval.
2.5 Trace antennadesigns Not applicable
Not applicable
2.6 RF exposureconsiderations
This equipment complies with FCC radiation exposure limits setforth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator & your body.