User Manual

ManualsBrandsRadioddity ManualsElectronicsTwo way radio

GM-N1 MANUAL

Functions and Operations

1. Powering On/Off

Turn the Power/Volume Knob clockwise to switch the transceiver power ON till a click is heard.

2. Selecting a Channel

Press UP/DOWN Key to select a desired channel. Press UP key to increase the channel, press

DOWN key to decrease the channel.

3. PTT (push to talk) Button

Press PTT key , then speak into the microphone to call.

Release it to receive.

4. Noise Cancelling (Press and hold the [NC] button to activate)

Long press Noise Cancelling Button for 2 seconds to turn on noise cancelling function until a beep

is heard and the noise cancelling indicator lights blue when transmitting. This function can also be

turned on/off even during a call.

5. Monitor (Press and hold the [Channel -] to activate)

Use the Monitor function to check if a channel is currently in use by others.

When an empty channel is located, you will hear continuous static and noise on that channel.

6. Time-out Timer(TOT) (Programmable on PC)

The purpose of the Time-out Timer is to prevent any caller from using a channel for an extended

period of time. If you continuously transmit for a period of time that exceeds the programmed

time set by programming software, the transceiver will stop transmitting and an alert tone will

sound. To stop the tone, release the PTT key.

7. Scan (Press [NC] button to get into scan mode)

When a transceiver is set by programmable software as scannable, press the channel select key to

channel 16, the transceiver will automatically detect the activities of scannable channels from 1 to

16, (programmable software can define different channels to be scannable or unscannable). When

a scanned channel has signals, transceiver will automatically stay in this channel for talking.

Note:

Transceiver will stay in a channel having signals, 5 seconds after the signals disappear, it will

continue scanning next channels.

When there are less than 2 scannable channels, it can not scan.

8. Battery Save

Battery Save function will decrease the amount of power used when a signal is not being received

and no operations are being performed(no keys are being pressed, and no switches are being

turned). While the channel is not busy and no operation is performed for 5 seconds, battery save

turns ON. When a signal is received or an operation is performed, battery save turns OFF.

9. Busy Channel Lockout(BCL)

Summary of content (4 pages)

PAGE 1
GM-N1 MANUAL Functions and Operations 1. Powering On/Off Turn the Power/Volume Knob clockwise to switch the transceiver power ON till a click is heard. 2. Selecting a Channel Press UP/DOWN Key to select a desired channel. Press UP key to increase the channel, press DOWN key to decrease the channel. 3. PTT (push to talk) Button Press PTT key , then speak into the microphone to call. Release it to receive. 4.
PAGE 2
When activated, BCL prevents you from interfering with other parties who may be using the same channel that you selected. Pressing the PTT switch while the channel is in use will cause your transceiver to emit an alert tone and transmission will be inhibited(you cannot transmit). Release the PTT switch to stop the tone and return to receive mode. Note: Busy Channel Lockout shall be setup in PC software. 10. High/Low Power Output Switch the power output between high and low in PC software.
PAGE 3
Ch.No. Tx Freq.(MHz) Rx Freq.(MHz) Ch.No. Tx Freq.(MHz) Rx Freq.(MHz) 1 462.5625 462.5625 15 462.5500 462.5500 2 462.5875 462.5875 16 462.5750 462.5750 3 462.6125 462.6125 17 462.6000 462.6000 4 462.6375 462.6375 18 462.6250 462.6250 5 462.6625 462.6625 19 462.6500 462.6500 6 462.6875 462.6875 20 462.6750 462.6750 7 462.7125 462.7125 21 462.7000 462.7000 8 467.5625 467.5625 22 462.7250 462.7250 9 467.5875 467.5875 23 467.5500 462.5500 10 467.
PAGE 4
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.