DRAFT COPY OF THE INSTRUCTION MANUAL (UC723) Precautions Before you read anything else, please observe the following: Warning! Corporation DOES NOT represent this unit to be waterproof. To reduce the risk of fire, electrical shock, or damage to the unit, DO NOT expose this unit to rain or moisture. Rechargeable Nickel-Cadmium Battery Warning This equipment contains a Rechargeable Nickel-Cadmium Battery. Cadmium is a chemical known to the State of California to cause cancer.
Important Safety Instructions When using your telephone equipment, these basic safety precautions should always be followed to reduce the risk of fire, electrical shock, and injury to persons: 1. Read and understand all instructions. 2. Follow all warnings and instructions marked on the product. 3. Unplug this product from the wall outlet before cleaning. Use a dry cloth for cleaning without liquid or aerosol cleaners. 4.
11. To reduce the risk of electric shock, do not disassemble this product. Take it to qualified service personnel when service or repair work is required. Opening or removing covers may expose you to dangerous voltages or other risks. Incorrect re-assembly can cause electric shock when the appliance is subsequently used. 12. Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: A. When the power supply cord is damaged or frayed. B.
, Exercise care in handling the battery in order not to short the battery with conducting materials such as rings, bracelets, and keys. The battery or conductor may overheat and cause burns. 5. Charge the Battery Pack provided with or identified for use with this product only in accordance with the instructions and limitations specified in the instruction manual provided for this product. 6. Observe proper polarity orientation between the Battery Pack and battery charger.
switches. Auto Standby* allows you to hang up by simply returning the Handset to the Base Unit. Auto Channel Scan During a call, your phone constantly monitors the noise levels of the channel. |f the channel becomes toe noisy, the unit automatically switches to a clearer channel to maintain the best transmission quality. Spread Spectrum Technology provides a digital link between the Base Unit and Handset.
Telephone Line Problems The FCC has granted the telephone company the right to disconnect service in the event that your phone causes problems on the telephone line. Alas, the telephone company may make changes in facilities and services which may affect the operation of your unit. However, your telephone company must give adequate notice in writing prior to such actions to allow you time for making necessary arrangements to continue uninterrupted service.
of radio waves which are broadcast over the open airways. Because of the inherent physical properties of radio waves, your communications can be received by radio receiving devices other than your own cordless telephone unit. Consequently, any communications using your cordless telephone may not be private.
or a telephone supply store for advice about the proper adapter or converter for your particular situation. Connecting the Telephone Cords Consider these safety guidelines before connecting the telephone cords: Caution! % Never install telephone wiring during a lightning storm. + Never touch uninitiated telephone wires or terminals unless the telephone line has been disconnected. % Use caution when installing or modifying telephone lines.
4. Plug the other end of the cord into the telephone jack on the wall. 5. Plug the AC Adapter into a standard 120 VAC wall outlet. Do not use an outlet contrived by a wall switch. Use only the AC Adapter supplied with this phone. 8. Place the Base Unit on a desk or tabletop. In desk or table top installation, the Handset is designed to stand only vertically in the Base Unit. DO NOT lay the Handset down on the Base Unit.
x Select a location away from electrical cables, pipes, or other items behind the mounting location that could cause a hazard when inserting screws into the wall. % Make sure the wall material is capable of supporting the weight of the Base Unit and Handset. % Use #10 screws with anchoring devices suitable for the wall material where the Base Unit will be placed. 1. Insert two mounting screws inches apart. Allow about 3/16 of an inch between the wall and screw heads for mounting the phone. 2.
1. Press in on the Battery Cover Release and slide the battery compartment cover down. 2. Align the plastic connector of the Nickel-Cadmium battery pack with its socket and plug it in. 3. Place the battery pack inside the battery compartment and slide the battery cover back on. Charging the Battery Pack Initial Battery Charging The rechargeable Nickel-Cadmium battery pack must be fully charged before using your phone for the first time.
Cleaning the Battery Contacts To maintain a good charge, it is important to clean all charging contacts on the Handset and Base Unit about once a month. Use a pencil eraser or other contact cleaner. Do not use any liquids or solvents. Adjusting Ringer Controls Ringer Tone and Volume The phone has 2 ringer tones with two volume levels each one soft and ane loud. To change the ringer tone and volume: While the phone is not in use, press ringer key. The ringer tone sounds and change volume.
on the Base Unit or press talk again while holding the Handset close to the Base Unit. Flash and Page/Find To access call waiting while the phone is in use or to use the one-way page to locate the Handset, follow these steps: Press These Keys You Will Hear If the call waiting tone sounds, press flash to accept the waiting call and put the first call on hold. A click, a short pause, then the caller (if you were on a call).
6. Enter the one-digit memory location Example: for memory location 5, you would press 5. Storing a Mixed Number If your phone is set up for Pulse dialing, you can store a mixed mode number so that you can easily access long distance services. Use these keys to store a mixed mode number in memory. 1. Remove Handset from the Base Unit. 2. Press mem . The talk & bat low LED blinks. 3. Enter the number to be dialed in pulse mode. 5851212 4, Press tone on the Handset. 5.
Example: for memory location 2, you would press 2. If you enter a invalid one-digit memory location, a loud single beep sounds. Chain Dialing On certain occasions, after dialing a number, you may be requested by the party or service you are calling to enter a special access code, such as when performing a banking transaction. To do this, simply: 1. Store the access code into one of the memory numbers. 2. Dial the main number. 3.
Problem Suggestion Charge light won't come on when Handset is placed in Base Unit, 0 Make sure AC Adapter is plugged into the Base Unit and wall outlet. o Make sure Handset is properly seated in Base Unit. o Make sure that the charging contacts on the Handset and Base Unit are clean. o If the phone is desk/table top installed, make sure the Handset is in the vertical position. Audio sounds weak and/or scratchy. o Make sure that the Base Unit antenna is vertical.
