User manual

ManualsBrandsRADWAG ManualsKitchen AppliancesAS 3Y

111

112

113

114

115

116

117

118

119

120

Table Of Contents

1. BASIC INFORMATION
- 1.1. Intended use
- 1.2. Precaution measures
- 1.3. Warranty
- 1.4. Supervision over balance metrological parameters
- 1.5. Manual significance
- 1.6. Balance user training
2. TRANSPORT AND STORAGE
- 2.1. Packaging
3. UNPACKING, INSTALLATION AND COMMISSIONING
- 3.1. Installation and place of use
- 3.2. Unpacking
- 3.3. Balance cleaning
- 3.4. Plugging to mains
- 3.4. Connecting peripheral equipment
4. GETTING STARTED
5. BALANCE LEVELING
- 5.1. Level control system – automatic operation – “ALERT” mode
- 5.2. Manual leveling
6. MENU STRUCTURE
- 6.1. Working mode selection
- 6.2. Moving in user menu
- 6.3. Return to weighing mode
- 6.3. Quick return to weighing mode
7. WEIGHING
- 7.3. Use of constant tare in weighing
- 7.4. Applying automatic tare in weighing
- 7.5. Digital tare
8. BASICS ON TERMINAL AND SOFTWARE OEPRATION
- 8.1. Basics on balance operation
9. BALANCE SOFTWARE
- 9.1. Operators / User profiles
- 9.2. System settings
- 9.3. Working modes
10. BALANCE ADJUSTMENT
- 10.1. Adjustment report settings
- 10.2.Adjustment history
11. DISPLAY CALIBRATION
12. BALANCE USER SELECTION
13. PERIPHERALS
14. ABOUT
15. COMMUNICATION
16. UPDATE
17. LEVELING
18. BALANCE ADAPTATION – USER SETTINGS
- 18.1. Adding a new operator
- 18.2. Deleting a operator
- 18.3. Selecting a operator
- 18.4. Operator settings
- 18.5. Quick access to determining working modes parameters
- 18.6. Parameter of working mode WEIGHING – quick access keys
- 18.7. Parameter of working mode WEIGHING – information
- 18.8. Parts Counting
- 18.9. Checkweighing
- 18.10. Dosing
- 18.11. Percent setup
- 18.12. Animal weighing
  - 18.12.1. Internal settings of the animal weighing mode
  - 18.12.2. Animal weighing mode – manual mode of operation
- 18.13. Density of solids, liquid and air
  - 18.13.1. Setting a default function of the density determining mode
  - 18.13.4. Density of air
- 18.14. Formulations
  - 18.14.1. Designing a formulation
  - 18.14.2. Use of database of formulations in weighing.
- 18.15. Statistics
  - 18.15.1. Internal menu of Statistics mode
- 18.16. Mass Comparison
- 18.17. Differential weighing
19. ACCESS TO BALANCE PARAMETERS
20. TECHNICAL DATA
- 20.1. Balance MYA .3Y series
APPENDIX A – cooperation with EPSON printer
APPENDIX B – cooperation with KAFKA printer
APPENDIX C – cooperation with label printer CITIZEN
APPENDIX D – databases

- 118 -

Cable: balance – printer (CITIZEN, EPSON)

Caution:

It is recommended to use peripheral equipment supplied by the manufacturer.

APPENDIX B – cooperation with KAFKA printer

An KAFKA printer is a device subordinate to a balance, thus any data is sent from

balance level. Correct cooperation between a balance and a printer requires setting

the same baud rate for both devices. Standard balance baud rate is set to 4800

bit/sec.

The baud rate setting in a KAFKA printer is carried out using micro switches.

Changing baud rate settings in a balance

PROCEDURE:

o Press SETUP pictogram or press SETUP button

o To open a screen on balance internal settings – press PERIPHERALS pictogram

o Press PRINTERS field and set:

− Printer type to NO

− Printer port as RS 232

o Check transmission parameters for the

RS 232 socket if used, and set:

− Baud rate: 9600

− Parity: no

− Data bit: 8 bits

− Stop bits: 1bit

− Handshake: no

o Return to weighing with procedure of saving changes.