User manual

ManualsBrandsRADWAG ManualsKitchen AppliancesAS 3Y

Table Of Contents

1. BASIC INFORMATION
- 1.1. Intended use
- 1.2. Precaution measures
- 1.3. Warranty
- 1.4. Supervision over balance metrological parameters
- 1.5. Manual significance
- 1.6. Balance user training
2. TRANSPORT AND STORAGE
- 2.1. Packaging
3. UNPACKING, INSTALLATION AND COMMISSIONING
- 3.1. Installation and place of use
- 3.2. Unpacking
- 3.3. Balance cleaning
- 3.4. Plugging to mains
- 3.4. Connecting peripheral equipment
4. GETTING STARTED
5. BALANCE LEVELING
- 5.1. Level control system – automatic operation – “ALERT” mode
- 5.2. Manual leveling
6. MENU STRUCTURE
- 6.1. Working mode selection
- 6.2. Moving in user menu
- 6.3. Return to weighing mode
- 6.3. Quick return to weighing mode
7. WEIGHING
- 7.3. Use of constant tare in weighing
- 7.4. Applying automatic tare in weighing
- 7.5. Digital tare
8. BASICS ON TERMINAL AND SOFTWARE OEPRATION
- 8.1. Basics on balance operation
9. BALANCE SOFTWARE
- 9.1. Operators / User profiles
- 9.2. System settings
- 9.3. Working modes
10. BALANCE ADJUSTMENT
- 10.1. Adjustment report settings
- 10.2.Adjustment history
11. DISPLAY CALIBRATION
12. BALANCE USER SELECTION
13. PERIPHERALS
14. ABOUT
15. COMMUNICATION
16. UPDATE
17. LEVELING
18. BALANCE ADAPTATION – USER SETTINGS
- 18.1. Adding a new operator
- 18.2. Deleting a operator
- 18.3. Selecting a operator
- 18.4. Operator settings
- 18.5. Quick access to determining working modes parameters
- 18.6. Parameter of working mode WEIGHING – quick access keys
- 18.7. Parameter of working mode WEIGHING – information
- 18.8. Parts Counting
- 18.9. Checkweighing
- 18.10. Dosing
- 18.11. Percent setup
- 18.12. Animal weighing
  - 18.12.1. Internal settings of the animal weighing mode
  - 18.12.2. Animal weighing mode – manual mode of operation
- 18.13. Density of solids, liquid and air
  - 18.13.1. Setting a default function of the density determining mode
  - 18.13.4. Density of air
- 18.14. Formulations
  - 18.14.1. Designing a formulation
  - 18.14.2. Use of database of formulations in weighing.
- 18.15. Statistics
  - 18.15.1. Internal menu of Statistics mode
- 18.16. Mass Comparison
- 18.17. Differential weighing
19. ACCESS TO BALANCE PARAMETERS
20. TECHNICAL DATA
- 20.1. Balance MYA .3Y series
APPENDIX A – cooperation with EPSON printer
APPENDIX B – cooperation with KAFKA printer
APPENDIX C – cooperation with label printer CITIZEN
APPENDIX D – databases

- 76 -

18.11. Percent setup

Percent setup is a mode intended to compare weighed load with a

pre-determined reference mass. The process is expressed in [%].

When declaring the mass to be compared, a user should specify

mass value, e.g. 50.0g, to be recognized by the balance as e.g.

100%. This is the reference point for the consecutive measurements.

Additionally, the percent setup mode can have the DOSING and CHECKWEIGHING

modes enabled.

The Quick access keys displayed in the bottom bar relate to the percent setup mode.

Set their attribute to Yes (present in the bottom bar) or No (absent).

Adjustment

Reference mass

Set tare

Checkweighing

Enable tare

Dosing

Print header

Database of reference standards

Print footer

Set 100%

Clear counter

Statistics

ID definition xxx Non-standard buttons

Principle of use and function of the quick access keys has been described in chapter

18.6. of this user manual: Parameter of working mode WEIGHING – quick access

keys.

Other quick access keys function in accordance with the description provided in

chapter 18.7.

Information items related to percent setup:

o bargraph

o supplementary unit

o tare

o gross

o counter