INSTRUCTION MANUAL 20” High Velocity Pedestal Fan MODEL NUMBER: BDHS-6120 USA & Canada Customer Service Number: 1-888-773-8744 www.BlackandDecker.
SAFETY INFORMATION WARNING 1. Always unplug the fan before moving it or performing maintenance. Never touch the fan with wet hands. 2. The fan should always be disassembled, repaired or rebuild by a qualified electrician. 3. Always unplug the fan when not in use. 4. Never unplug the fan by pulling the power cord, always do it by holding the plug. 5. Never use the fan if the power cord or plug is damaged. Discard the fan or return it to an authorized service agent for examination and/or repair. 6.
PACKAGE CONTENT Part Description Quantity 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Front Guard Blade Rear Guard Motor Bracket Screw M6X40 Washer #6 Nut M6 Inner Tube Height Adjust Knob Outer Tuber Base Cap Screw M5x30 Flat Washer #5 Spring Washer #5 Base 1 1 1 1 1 2 2 2 1 1 1 1 4 4 4 1 3
CARE AND MAINTENANCE Unplug the appliance before cleaning. Do not use water to clean metal surfaces. Slightly moisten a cloth with a mild cleaner and then wipe off the surfaces of the fan. In order to remove dust from the protective guard, use a vacuum cleaner or remove the front protective guard using a screwdriver to unscrew the securing screws on the edges of the guard. After cleaning, replace the safety guard, and fasten the securing screws on the edges of the protective guard.
Step 3 Slide the height adjustable ring into the inner Tube (9). Then, out it into the outer tube (11) and fasten the height adjustable ring (10) to the desired height. Step 4 Connect the fan head (1, 2 & 3) with the inner tube (9). Then firmly tighten two sets of screws (6), washers (7) and nuts (8) in the holes of the fan. Caution: the screws must be fully tightened before operating the fan.
OPERATING INSTRUCTIONS 1. Adjust the desired speed by rotating the knob: 0: Stop- 1:Low- 2: Medium- 3: High 2. Tilt the fan head upward or downward for the desired direction of air flow. PROBLEM The fan fails to operate MAIN SPECIFICATIONS MODEL No. BDHS-6120 POSSIBLE CAUSE 1.Fan is not plugged in CORRECTIVE ACTION 1. Make sure the fan is plugged in, and the power outlet is working properly. 2. There may be some obstructions in the fan. 2.
Black & Decker and the Black and Decker logo are trademarks of the Black & Decker Corporation and are used under license. All rights reserved. Product may differ slightly from the picture on the cover of this instruction manual. Not all accessories shown in the photography are included in this package. 3 Year limited warranty: Covers all defective materials and workmanship under normal household use.
MANUAL DE INSTRUCCIONES Ventilador de Pie de Alta Velocidad de 20 pulgadas MODELO NÚMERO: BDHS-6120 Para servicio al cliente en Estados Unidos y Canadá llame al: 1-888-773-8744 www.BlackandDecker.
LEA ESTE MANUAL CUIDADOSAMENTE ANTES DE OPERAR- GUÁRDELO PARA FUTURAS REFERENCIAS INFORMACIÓN DE SEGURIDAD ADVERTENCIA 1. Siempre desenchufe el ventilador antes de moverlo o de hacerle mantenimiento. Nunca toque el ventilador con las manos mojadas. 2. El ventilador siempre debe ser desarmado, reparado o reconstruido por un electricista calificado. 3. Siempre mantenga el ventilador desenchufado cuando no lo esté usando. 4.
CONTENIDO DEL PAQUETE Parte 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Descripción Protector Frontal Aspas Protector Trasero Motor Soporte Tornillo M6X40 Arandela #6 Tuerca de Sguridad Tubo interno Perilla de Ajuste Tubo externo Tapa de base Tornillo M5X30 Arandela Plana #5 Arandela #5 Base Cantidad 1 1 1 1 1 2 2 2 1 1 1 1 4 4 4 1 10
INSTRUCCIONES DE ENSAMBLAJE Paso 1 Una el tubo exterior (11) a la base con los cuatro tornillos (13) como se muestra en la imagen. Precaución: Los tornillos deben apretarse completamente antes de operar el ventilador Paso 2 Deslice el anillo ajustador (10) de altura fuera del tubo exterior (11).
Paso 3 Deslice el anillo ajustador (10) de altura sobre el tubo interior (9), luego sobre el tubo exterior (11) y asegure el anillo ajustador (10) de altura en la altura deseada. Paso 4 Conecte el cabezal del ventilador (1, 2, & 3) con el tubo interior (9). Luego apriete firmemente dos juegos de tornillos (6), arandelas (7) y tuercas (8) en los orificios del ventilador. Precaución: los tornillos deben apretarse completamente antes de operar el ventilador.
INSTRUCCIONES DE OPERACIÓN 1. Ajuste la velocidad deseada girando la perilla: 0: Detener- 1: Baja – 2: Media3: Alta. 2. Incline la cabeza del ventilador hacia arriba o hacia abajo, para poner la dirección del flujo de aire hacia el lado deseado. PROBLEMA POSIBLE CAUSA El ventilador no funciona 1. El ventilador no está enchufado 2. Puede haber algo obstruyendo el ventilador . CARACTERISTICAS PRINCIPALES MODELO No. TAMANO DEL ASPA BDHS-6120 500 MM 20 PULGADAS ACCION CORRECTIVA 1.
Black & Decker y el logotipo de Black & Decker son marcas comerciales de The Black & Decker Corporation y se usan con licencia. Todos los derechos reservados. El producto puede diferir levemente de la imagen que se encuentra en la tapa de este manual de instrucciones. No todos los accesorios ilustrados en la fotografía se incluyen en este paquete. La garantía de 3 años cubre todos los defectos referentes al material y envío cuando se usa en condiciones normales y correctas para uso doméstico.
MANUEL D L’UTILISATEUR VENTILATEUR SOCLE (SUR PIED) 20IN NUMÉRO DE MODÈLE : BDHS-6120 Pour le service à la clientèle aux États-Unis et de Canada, appelez le: 1-888-773-8744 www.BlackandDecker.
CONSIGNES DE SÉCURITÉ AVERTISSEMENT 1. Débrancher le ventilateur avant de le déplacer ou de faire l'entretien. Ne touchez pas le ventilateur lorsque vos mains sont mouillées. 2. Uniquement les électriciens qualifiés devraient démonter, réparer ou reconstruire le ventilateur. 3. Débrancher le ventilateur lorsqu'il n'est pas en cours d'utilisation. 4. Débrancher le ventilateur en tenant le câble. Débrancher en tenant la fiche. 5.
Diagramme Partie Description Quantite 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Protecteur Avant Pale Protecteur Posterieur Moteur Support Vis M6X40 Rondelle #6 Ecrou de blocage Tuyau interieur Bouton de réglage de hauteur Jonction Capuchon de la base Vis M5X30 Rondelle piso #5 Rondelle Base 1 1 1 1 1 2 2 2 1 1 1 1 4 4 4 1 17
INSTRUCTIONS DE MONTAGE Étape 1 Fixez le tube extérieur (11) à la base avec les 4 vis comme (13) illustré. Attention : Les vis doivent être serrées complètement avant le fonctionnement du ventilateur. Étape 2 Glissez l'anneau ajustable (10) de l’hauteur loin du tube extérieur (11). Gardez-le pour être utilise a l’étape 3.
Étape 3 Prenez l'anneau ajustable (10) de la hauteur dans le tube intérieur (9). Puis mettre dans le tube extérieur (11) et serrer la bague pour l’ hauteur désirée du ventilateur. Étape 4 Connecter la tête du ventilateur (1, 2, &3) avec le tube intérieur (9). Puis serrez fermement ensemble deux des vis (6), des rondelles (7) et des écrous au niveau des trous (8) de la tête du ventilateur. Attention : les vis doivent être serrées complètement avant le fonctionnement du ventilateur.
INSTRUCTIONS D'UTILISATION 1. Réglage de la vitesse désirée en tournant le bouton de l'interrupteur : 0 : Arrêter- 1: Moyen - 2: Bas - 3 : Haut 2. Incliner la tête du ventilateur vers le haut ou vers le bas pour votre direction souhaitée du flux d'air. PROBLEME Le ventilateur ne fonctionne pas POSSIBLE CAUSE MESURE CORRECTIVE 1.Le ventilateur n’est pas branche 1. Assurez-vous que le ventilateur est branche et que la prise de courant fonctionne correctement 2.
La mention Black & Decker et le logo Black & Decker sont des marques de commerce déposées de Black & Decker Corporation el sont utilizes en vertu d’une licence. Tous droits reserves. Le produit emballé peut différer légerément de celui illustré. Les accessories illustrés ne sont pas tous compris dans l’emballage. La garantie de 3 ans couvre tout vice de matériau et de main-d’ouvre lorsque utilisé dans des conditions normales d’utilisation au foyer.