2” 3 Speed Desk Fan INSTRUCTION MANUAL MODEL NUMBER: RDF-1220 120VAC 60HZ 40W For customer service in USA and Canada please call: 1-866-499-6389 WWW.RAGALTAUSA.
IMPORTANT SAFEGUARDS Definitions Whenever used, the following identify safety and property damage messages and designate a level of hazard seriousness. - This is the safety alert symbol. It alerts you of potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER – Indicates an imminently hazardous situation, which, if not avoided, will result in death or serious injury. Usage of this signal word is limited to the most extreme situations.
Do not operate the product if it has a damaged or cut power cord or plug, if wires are exposed, if it malfunctions, if it is dropped or damaged, or if it is dropped in or exposed to water. This product has no user-serviceable parts. Do not attempt to examine or repair this product yourself. Only qualified service personnel should perform any servicing; take the product to the appliance repair shop of your choice for inspection and repair.
To Assemble 1. Remove the Base Nut from the bottom of the Fan Assembly by turning it counterclockwise. 2. Place the bottom of the Fan Assembly into the Base, and then replace the Base Nut. 3. Remove the Spinner and the Locking Nut from the Motor Shaft by turning them in the direction of the arrow marked LOOSEN. 4. Align and place the Rear Guard, Handle on top, on the Motor Shaft and against the Motor Housing (see Fig. 1). 5.
Clean the exterior surfaces only by wiping with a soft, damp cloth. Dust can be removed from the Guard (Grill) using a small vacuum cleaner. WARNING: Do not allow water or other liquids to enter the interior of the product. NOTICE: Do not use abrasive cleaners/pads to clean the product, and do not disassemble this product for cleaning its internal parts, as doing so may result in product damage and will void the warranty.
Ventilador de Mesa de 3 Velocidades de 30.48cm MANUAL DE INSTRUCCIONES NUMERO DE MODELO: RDF-1220 120V AC/60 Hz, 40 W Para servicio al cliente en USA y Canadá llame al: 1-866-499-6389 WWW.RAGALTAUSA.
MEDIDAS IMPORTANTES DE SEGURIDAD Definiciones Siempre que se utilice, lo especificado a continuación identifica los mensajes de seguridad y daño a la propiedad e indica el nivel de gravedad del riesgo.Este es el símbolo de alerta de seguridad. Lo alerta de posibles peligros de lesiones personales. Obedezca todos los mensajes de seguridad que siguen a este símbolo para evitar posibles lesiones o la muerte.
No sumerja este producto, el cable de energía o el enchufe en agua u otros líquidos. No coloque el producto en o cerca de una ventana abierta pues la lluvia, nieve o granizo podría caer dentro del producto y provocar un corto-circuito. Si utiliza un cable de extensión con este producto, el valor eléctrico nominal del cable de energía, o del cable de extensión, debe ser al menos tan alto como el valor eléctrico, o voltaje del producto.
GUARDE ESTAS INSTRUCCIONES PARA FUTURA REFERENCIAS Partes Para Ensamblar 1. Saque la Tuerca Base de la parte de abajo del Montaje del Ventilador rotándola en sentido contrario a las agujas del reloj. 2. Coloque la parte de abajo del Montaje del Ventilador dentro de la Base y luego vuelva a colocar la Tuerca Base. 3. Saque el Rotador y la Tuerca de Bloqueo del Eje del Motor rotándolas en dirección de la flecha que dice AFLOJAR. 4.
8. Abra las Abrazaderas del Protector Delantero y luego conecte el Gancho del Borde del Protector Delantero sobre la clavija mas alta del Protector Trasero (ver Figura 2). 9. Jale hacia abajo para encajar el Gancho del Borde en su sitio, y luego cierre cada Abrazadera sobre ambos Protectores para asegurarlo (ver Figura 2) Para Usar PRECAUCION: Asegúrese de que el producto está totalmente armado antes de enchufarlo en una tomacorriente eléctrico.
Limpie las superficies exteriores solo con un paño suave y húmedo. Para sacar el polvo que está dentro del Protector (Rejilla) use una aspiradora pequeña. ADVERTENCIA: No permita que el agua u otros líquidos se introduzcan en el interior del producto.